JBC17G*R3 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lavona from JACKSONVILLE, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Bake element burned out
Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from BLUFFTON, SC
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken heating element
remove broken heating element and install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FALL RIVER, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bottom oven heating element was out
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Grand Rapids, MI
- Parts Used:
- WB44X5082
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Really old range. Broken bake element in oven.
Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miranda from UNION GROVE, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom Bake Element had burnt into/split
Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bar Harbor, ME
- Parts Used:
- WB31K10266
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burned/scorched corroded drip bowl
No brainer. No tools. Remove burner, lift out old drip bowl, drop in new one, plug in burner, voila! Done. 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST WARWICK, RI
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
a plug on the element broke off while cleaning and replacing
Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Sewickley, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven wouldn't heat
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is still a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosaire from St. Agatha,, ME
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element was cut
Removed two screws and take Element out and put new one in.It is very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bet from Bothell, WA
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
the burner trays just needed replaced for an 85 year old senior citizen
Removed burner trays, pulled out heater unit, cleaned up inside of area around all four burners, slipped the burner trays back in and pushed the heater unit back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fran from Goldsboro, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bake element burned up
This was extremely easy to replace. When I told my mom I would replace it for her, she thought I was crazy. When she saw how easy it was, she finally understood. I had to remove the two screws holding the element in place. I pulled it out about 3 inches and unscrewed one screw for one wire. I didn't want to lose the wire, so I immediately connected the wire to the new element. I disconnected the second wire and attached it to the new bake element. Then attached the two screws putting the plate back up, securing the element. So easy! Just unscrewing and replacing 4 screws and I was done!! Took less than 10 minutes. I didn't have any real tools available, so I used a small adjustable wrench and it worked fine. The best part was it was so easy we were able to have a working oven in time for Thanksgiving!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Burlington, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The bottom element in my oven quit working.
Pulled out the bottom drawer of the stove and discovered the plug. So the plug was pulled from the wall socket.
Before this I had sprayed the screws with WD-40 and let it sit for 2 days.
Screws came out easily. Pulled out the old element and removed screws. Screwed on new element on both sides. Put in place and put old screws back.
Plugged stove back in. Turned on stove. Element came right on.
Before this I had sprayed the screws with WD-40 and let it sit for 2 days.
Screws came out easily. Pulled out the old element and removed screws. Screwed on new element on both sides. Put in place and put old screws back.
Plugged stove back in. Turned on stove. Element came right on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Trinity, TX
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old wore out parts
just put in the new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Clayton, DE
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Original element stopped working
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.
Was this instruction helpful to you?
Thank you for voting!