JGB908SEL2SS General Electric Range - Instructions

Removed lower oven panel and replaced oven igniter.

Needed to replace the part in oven which lights the gas. My husband is more of a supervisor rather than a fix it yourself kind of guy. But he did it and it was hilarious watching him squeeze in a place meant for a smaller person with tiny hands, while holding the flashlight in his mouth. But the oven is fixed and works like brand new. Thank you

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.

removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!

Replaced the igniter. Quite simple.

Old school, so I first thought it had to be a thermostat, but realized it did not have a pilot light, but an igniter. Read a few stories of others who had the same issue. Ordered the part, came in early. By that time I knew what I had to do to replace it. Only issue was the part came with a male connector when the original was female. But part came with a couple of ceramic wire nuts, so I guess that is not uncommon. Cut the connectors off and used the wirenuts. Oven is working well.

Every part of the part replacement was easy with the exception of removing one of the two screws that were holding the igniter to gas bar. No fault of the part to be replaced in any way. One of the screws that hold the igniter to the gas bar stripped when I was attempting to remove it. Had to use a small cut off wheel and my dremel to cut the screw and then was able to remove it by screwing it all the way through the hole it was in. Then tapped the two existing screw holes to 10/32 and attached the igniter with new screws. Everything else was about as easy as you can get.

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

First removed 3 screws at burner front and back then pulled out lower storage drawer to disconnect plastic connector, removed and had to cut plastic connectors to use ceramic wire nuts (supplied with parts box) I had to work from underneath stove as well as in the oven it self, if the main door is easily removable it would have helped a great deal but four hours later

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.