JBP30BB1WH General Electric Range - Instructions

First I had to remove the oven ceiling screws bracing the broiler element. Second I removed the screws holding the connectors at the back of the oven before I could disconnect the two wires ( which were awkward for me to get to because I am 5'2" but was able to reach without removing the oven door).

I reconnected the two connectors and screwed the brace into the back of the oven. Then replaced the screws into the ceiling of the oven to hold the unit in place.

I was very pleased to have been able to do this project on my own and the broiler is working fine.

Pulled the oven out of it's location. Disconnected the power cord from the Electrical Outlet. Removed the Protective back plate (from the rear of the oven) which covers the wiring. Disconnected the two leads that connect the Baking Element. Went to the front of the Oven, opened the oven door, removed the two screws with a socket wrench (you can use a screw driver as well), at this point you can replace the element with the new one and secure with the two screws. I then went back to the rear of the oven and reconnected the two wires back onto the new heating element and replaced the wiring protective back plate. Reconnected the power cord to the electrical outlet and turned on the oven to see if the element heats up. AND IT DID. Moved oven back into it's original location and I was done. This took 16 minutes to do and saved me a nice amount of money. I could have had a service person show up and do this work which would have cost me $189.00 (Parts & Labor) to have done and all I spent , by ordering the part from PARTSELECT.COM, was just under $50.00.

Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

I (1) pulled the oven away from the wall to get the back of it exposed. Then I (2) pulled the plug out to make sure there was no electrical current. Then I (3) opened the oven door and tugged on the broken heating element to see how tightly it was connected in the back of the oven. Next I (4) went to the back again and slid the silver-colored metal cover that protected the exposed electrical wiring for the oven. I (5) observed that there were a number of different colored wires held in place by screws as well as some wires that disappeared into the insulation, so I (6) went back to the front of the oven and pushed the broken heating element backward to determine if its wiring would become visible from the back of the stove. I (7) observed from teh back that it did. From that point, I (8) pulled the heating element's wiring connections through the insulation until it was visible. The I (9) unscrewed the two nuts connecting the heating element to the oven's wiring. Then I (10) went back to the front and pulled the broken heating element out and (11)inserted the new heating element. Then I (12) returned to the back and connected the loose wires to the heating element and (13) pushed the heating element forward into the oven. I (14) went around to the front to ensure the heating element was positioned the same way in the oven as the old one was, then in the back (15) replaced the metal shield over the wiring and isulation, (16) plugged the oven back in and (17) turned the oven baking setting on to a high temperature to test the new element (i.e., that it was connected correctly and actually worked). I (18) observed that the oven began heating up quickly to the proper temperature, and I was greateful the new bake element worked as good the original part. I then (19) turned the oven off and pushed it all the way back to its place against the wall.

The repair job was not effortless (about 15-20 minutes) but was simple enough NOT to require an electrician. The most difficult part was physically sliding the stove out and back into its tight place between our counters.

First, I got my husband and let him know that the part was in (really easy), then I sat back and watched as he pulled the oven from the wall, unplugged it and lifted the stove top (so far, I haven't broken a sweat)! I then peeped up under the top as he removed a scew from the element and then several screws from the back panel, trace the wire to the needed element, and reconnect the new element (haven't broken a nail yet)! He then secured the element back on its mount, let down the top and plugged the oven back in, checked for accuracy...mission accomplished! This was the easiest repair I've ever done!

When we received the part (it would have been nice to get instructions, but we figured it out anyways). Took four screws out of the door. Took some nuts off the door. Spread the door, took out the old (a little tricky) and slid in the new. Replaced the nuts and then the screws and it was done.

Originally the burner had a hole burnt through it, which resulted in a hole being burnt through the bottom of a pan. I replaced the burner and it would not heat up. I removed the top control panel, after securing power to the stove outlet, turned the power back on checked both sides of the swith with a meter (with the switch on) and had no power on one side. I went to two stores that did not have the switch in stock and ended up ordering from this site at about half the price! It arrived a couple of days later. I marked the wire colors on the old switch, took off the knob, removed two phillips head screws, pulled out the old switch and installed the new one and I was back in business. The hardest part was getting the sheet metal / heat gaurd positioned right upon re-assembly. To remove the panel there are two screws in the rear (nut driver) and a screw on either side of the front under each corner that require a torx driver to remove.

I order the part online on the 23rd of February 09 in the afternoon it was delivered on the 24th to the address in Florida and then fedex to me in Cayman. So I got it on the 2nd of March went home that evening after work got my pliers unpluged the stove removed the two screws that holds the element in place. I also removed the metal from the back of the unit first to make sure I was doing it right. I then pulled the element at the back and disconnected the two wires replacing it with the new one. I then replaced the back and screws and pluged it in turned on the oven waited and when I saw it turn red I felt so good. I said thank you Lord and then baked a cake. The whole installation took about 20 mins.
Thanks again.
P.S. please look into offering shipping orders overseas.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

Threw the breakers off for the range. Removed the 2 screws on element connection end. Pulled element out 3 to 4 inches being careful not to scrape insulation on 220 wires. Had wife hold element from moving as I wiggled off the pair of wires from the element connectors. Next made sure wires were clipped in wooden sprung closepin to prevent slippage back into the rear of the hole in the oven. Next removed the screw holding the thermo lead being carefull not to kink or twist it. Removed the final 2 screws from the front hangers and removed the old unit from the cavity.

Placed the new unit in the cavity and slid the front clip backwards 3 inches to allow work romm when the unit was attached. Doing it this way allows the element to float so you have both hands to reconnect the 220 wires. After reconnecting then rescrew the thermo to the connection plate and carefully slide the unit backwards in the front clips allowing the wire connections to be put where they belong without touching the range sides or rear panel. Replace the final 2 screws when the unit is seated properly in the back wall.

Flip the breakers to on and test your handywork. You should see a glow off of the element in 30 seconds or less. Be aware a small bit of production lubricant may burn off with the first heating of the unit. No worry as it is a small wisp.

I dis asymbled the door to access the broken end cap screw holders(plastic) Take great caution with the door glass. It is held in place by thin stamped steel slots and when taking the door face apart, the glass is free to fall out. I placed four strips of adhesive tape on the glass to hold it in place while I replaced the handle end caps. Use an electric screwdriver to place the retainer screws. It speeds up the work, and allows your other hand to stabilize the door. Caution to not over torque the steel screws. They screw into plastic and can strip easy. Another point: These replacement End Caps did not come with any supporting hardware - screws. I was lucky in that I retained the original screws and they were in good condition and could be recycled. Very impressed with the service, would recommend to all. Frighteningly fast delivery. I was shocked to see the box on my porch in just a few days.

R/
CSB

Yeah, so I didn't read the manual the first time we ran the self-clean cycle on the oven. Something about taking the racks out. So these were my little reminder to never do that again. The old racks came out; the new ones went in. Ten seconds. On to the next embarrassment...

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.