JBS02BB1 General Electric Range - Instructions

Removed the old and slipped in the new.No problem and it works fine.

Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.

I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!

ordered new surface element and pushed in to conector turned on switch to test and works fine thanks

Disconnect power to range, remove fan cover (4 screws).
Remove old element (2 screws).
Pull off wires from old element.
Discard old element, clean bottom of oven.
Slip wires on terminals of new element.
Install new element,and fan cover.
Reconnect power.

Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!

It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!

ordered parts and disassembled old burners and installed new ones. All the parts were in the box when delivered.
Helping my 80 yr old mother-in-law very happy.

Got parts in for one of her 81st birthday present she was thrilled.

Used a nut driver and removed to studs and pulled the old element out and disconnected the two wires. Then connected the new element and put the studs back. It was that easy. Great website and it only took 5 minutes to order the part and received it on time. Plus my wife was trying to cook thanksgiving dinner. Thanks

I've been looking for an 8" replacement burner for my GE stove after my original burner caught on fire over a year ago. I had all but given up on finding a replacement after searching at all the stores in my area and also searching on the net. After cooking sides for Thanksgiving dinner this year and the pain of cooking with only 1 large burner, I decided to search again for a burner on line and thank goodness I found this site! All I did was put in the model number of my range/stove and the site directed me to the replacement burner. The picture of the burner looked like mine, so I decided to purchase it but I still wasn't convinced it would fit and work because of my failed previous burner purchases. I really thought my burner was too old and the part was no longer made. Well the part shipped very quickly and lo and behold it fit and worked! Installing was a breeze...I just snapped it in...thanks so much!

I ordered it on line and it was easy to fix, I had it done before my husband came home from work. I just undid the old one and pushed the new one on. I have to stay ordering from here was alot cheapier

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

First, used the nutdriver to remove the two screws that hold the element. Then pulled out the element 4 inches. Disconnected the two wires from the old element and discarded it. Connected the wires to the new element and tightened them a bit by squeezing with pliers (not too tight, but just enough so they won't disconnect easily). Pushed the wires back through the insulation and screwed the two nuts back in place, making adjustments so that the element is level.

I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the the two screws that connected the wires and element together. I then tried to connect the new element to the wires, but found that the screw holes were smaller than the original holes in the old element and the original screws wouldn't fit. No problem, I then got a cordless drill and found a drill bit a little bigger than the holes, I held the element connector with pliers and made the screw hole a little bigger, same with the other connector. I screwed the screws into the connectors with a socket wrench and then screwed the element back into the holes in the oven, then turned on the oven and it works as good as new.

Removed the cover plate, pulled the element out, removed the screws holding the wires in place, but then I had to enlarge the screw holes on the new element in order to fit the screws into the new element. Took a while with an awl to enlarge ther two holes. Connected the new element, pushed it back in and replaced the cover plate. Worked great.