JB940WY4 General Electric Range - Instructions

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.

Replaced it

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

REmoved the covers, removed the old part, be careful with the electrical connections, they move back behind the wall and are hard to get back in the open. While waiting for the new part, 2 days, I cleaned the oven. Works like new.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

The age of the system resulted in the cook top being heavily stuck by food-stuff to the range surface. The result was a twisting of the top when breaking it free. It caused the cooktop (a $500+ part) to crack diagonally across the whole surface. Thus ended the quick do-it-yourself process, and out to buy a new range. Parts-select was very good about the return process of the un-used and un-opened burner element.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

plug in thermistor when needed

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.

Good directions