JBP61WB2WW General Electric Range - Instructions

Removed the old handle with the new one.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Simply slide stove away from wall and unplug. Remove the center back plate on the rear of the stove, Open oven slide new element into rear of oven, snap into place. Return to rear of oven. slide wire connectors onto oven element prongs, replace center cover, make sure oven is turned off, plug stove back in and slide back into place. Open oven and turn on. allow element to heat up. Once the element has heated and the new burns off. Turn off the oven and replace the racks, This entire process took maybe 5 minutes.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

The only problem was m short arm and no good flash lights around

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

I unplugged th oven, for my safety. Removed 2 small bolt head screws, unplugged 2 wire connecters similar to car speakers connecters. Removed the element. Then took a few minutes to clean bottom of oven. It is so much easier with out the element. I plugged the wires onto new element, then i put the 2 small screws back in. Plugged in oven, pushed it back in place and turned on oven. It has been great! I think old element was unevenly heating. Baking has been noticable better. Thank you partselect.com. a very satisfied New England customer

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Remove center cover on back of stove exposing wiring. Unplug stove from 220v outlet. Unplug wires from old element.From inside stove, Remove 4,quarter inch screws holding back panel inside oven in place. Remove back panel from inside oven. Will be able to see the brackett on element and 2 screws holding the element/brackett in place, remove those 2 screws and remove old element. Reverse process to install new element.

I disconnected the power to the stove and it was very simple, undid the nuts with socket wrench pulled element out and diconnected the wires.I put the new element back in the same way the old one was removed .I am a 70 year old woman.The great part was the element was shipped out vey quickly! great service

Removed the 2 screws, unpluged the 2 wires and installed the new elment