JBP79WS1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rex from Colton, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element melted then naturally would not heat.
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I removed the old element from the oven and replaced it with the new element. Then I connected the two wires to the new element and pushed the element into place. Then I replaced the two screws that held the element in place. I then tested the oven and it worked wonderfully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from LEBANON, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Something Had Dripped Down On The Baking Element Causing It To Over Heat In One Spot And Short Out.
This was so easy to do. First I took the two screws out of the holding plate. Then the element comes out and I took the two screws attaching the wires to each end of the element out. To replace it just reverse the above and turn it on let it heat for about 10 mins to burn off any residue and you are ready to start baking again. Although not really necessary it is reccommended to unplug or turn of the breaker before you start working on the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Golden, CO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The heating element in the oven failed, after at least 16 years of good service.
First, we turned off power to the range. We removed the screws holding the element to the back wall of the oven and pulled out the element a few inches. We disconnected the 2 wires from the old element, and attached the new element with the 2 provided screws. We pushed the element back into the wall and secured it with the screws. Turned the power back on, turned the stove back on and, voila, the frozen pizza was well on its way to becoming dinner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr Sal from Eastampton, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
element wont heat up
4 screws 4 off then 4 on done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Clayton, DE
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Original element stopped working
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosaire from St. Agatha,, ME
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element was cut
Removed two screws and take Element out and put new one in.It is very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Cary, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The Bake Element broke and when powered on it started to spark and flame.
First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Tekoa, WA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The lower heating elemen went out. It looked like a welding rod
It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Chimacum, WA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven wouldn't heat, bake element burned out.
Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.
From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.
From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Cave Creek, AZ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking element no longer worked.
Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from BETHLEHEM, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The bake element burned in half.
First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from McKinney, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Bottom Element On The Top And Bottom Oven Burned Out
Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from snyder, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
boken element
remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Renton, WA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Oven lower Bake Element exploded
First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Slatington, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake element developed a hot spot that burned through it.
Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my finger to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.
Was this instruction helpful to you?
Thank you for voting!