JGBS04BEA2WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Norton from Malta, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One burner wouldn't light
Removed old and set inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia A from Newport, NH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gas flame flared and blackened pots; gas jets clogged
raised the range top so the supports locked in place. carefully lifted off the old burner assemblies. used a paper towel to remove any black soot from gas jets. opened the plastic package of the new burner assemblies, pulled out the new parts and carefully put them in place. turned on the flame to test... took less than 5 minutes to fix a problem that's been annoying for 3 years!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cincinnati, OH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
3 of 4 Burners would not light
Open the stove top pulled old burners out dropped new set in place. Theyclick right in NO TOOLS REQUIRED!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLORIA from RICHARDSON, TX
- Parts Used:
- WB31K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner grates on the gas range were the original ones and had to be replaced.
I was worried about getting the right part so I called customer service and told them the model number. They told me exactly which part would work and it did. I got the shipment very quickly (less than a week). And it was just like the original one and it was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baltimore, MD
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burners were scorched looking
lifted the old burners out and sat the the new ones in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamyra from Friendship, WI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove burners no longer working
Ordered 4 new burners, snapped the old ones out, put the new ones in and my stove works great. Also, I got my parts in 1 day. Very satisfied with my experience with PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from Carrollton, TX
- Parts Used:
- WB15X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Door Handle Broke
The repair was very easy. It did require a very small torx driver (I can't remember the size off hand.) and a 1/4" nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Birgit from Opelousas, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHANNA from GERMANTOWN, MD
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
both burners were bad
Just opened the box, removed the 2 old burners and replaced with the 2 shiny new ones. Yeah success! I placed my order for this product and before I knew it, it was at my front door. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Burlington, OK
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Would Not Turn Off
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me. . . . . . 25 Seconds or so and it went out. . . . . Job done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Geneseo, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from charles city, IA
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left oven door bracket broken
You need to remove both ends first you block up under the oven door so it is flat to work on then, you will see inside the door the to sleeves that the long screw goes through is easier to screw back in,you are on the road to finished product. H.l.R
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from Waterloo, IA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Thermostat knob broke off
Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Yadkinville, NC
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
handles broken on oven door
removed old handles and slid door apart align new handles and re-installed new handles. One person job.
Was this instruction helpful to you?
Thank you for voting!