JKP27BD1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- eddie from GALES FERRY, CT
- Parts Used:
- WB44T10031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking element was not working
Pulled out oven and removed the 3 bolts on the back panel exposing the connector to the temp sensor. Unclipped it. Went in oven and removed the bolts inside as well. Used a wire coat hanger to feed the new sensor line through the back and reversed the steps. Didn’t think it would work but it’s not always a bad element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from townshend, VT
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was not getting up to temp
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Paris, TN
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
F2 error when oven was heating up, along with a beeping noise and then it shut off
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Harkers Is., NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven slow to heat up
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Tracy, CA
- Parts Used:
- WB44T10031
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replacement Lugs different from original
Cut off original termination lugs and re-crimp new lugs to match the replacement element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MILLER PLACE, NY
- Parts Used:
- WB32T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn oven door gasket
simply pry off the old gasket and lay new gasket in place and press pins into slots
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Salem, OR
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flashing F2 and erratic temperature readings.
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Green Valley, AZ
- Parts Used:
- WB24T10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Switch
I unplugged the defective plug and replaced it with the new one. Took 5 min total
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jud from gatesville, TX
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
F2 error code
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lisle, IL
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven not warming, f2 indicating overheat
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Thornton, CO
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven lights were burning out regularly
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Katy, TX
- Parts Used:
- WB44T10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broiler element burnt out
Unscrewed back plate, unplugged old unit, plugged in new unit and ready to go. Don't forget to turn off circuit breaker for oven before starting !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from gap, PA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
f-2 or f-3
remove two bolts in on sensor and slip thru back un plug and reverse to put in
Was this instruction helpful to you?
Thank you for voting!