JCSP31WV2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Boise, ID
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
10-yr old Baking Element gave out
This repair was idiot-proof. Removed 2 screws, unplugged the old part, plugged in the new one, and replaced the 2 screws.
Literally a 2 minute repair!!
Literally a 2 minute repair!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Gladstone, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Element no longer heated
Piece of cake. 2 screws and a flashlight. I needed needle nose pliers to insert the "plugs" into the "sockets."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Newnan, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Defective
Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Trenton, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Existing Element Broke
removed two bolts on the inside of the oven, disconnected the two electrical connections in back which were a little set so I had to use pliers and removed old element. Reversed procedure to install new element.
The >15 minutes includes vacuuming out the oven.
partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.
The >15 minutes includes vacuuming out the oven.
partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Crescent City, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out surface element
simply by inserting new replacement into electrical socket ...very satisfied in new replacement price and quick delivery date Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Catasauqua, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven wouldn't heat
Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Newport, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
the old oven element burned in two.
After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element cracked/split - open circuit
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.
Al S.
Al S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from mastic, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bake element burns out heating up easter dinner
Uplugged the oven and undid the back contact cover, removed the nuts inside the oven and slid out the element. Pushed the new element into place and secured it. Attached the contacts and replaced the cover. Plugged it in and got cookin'.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Cincinnati, OH
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A teapot melted on one of two working burners
Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!
It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!
It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joey from barto, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bake element had broke and caught fire
It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Murray from Franklin Square, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element burned out, lower unit
removed nuts from inside, removed rear panel, pulled old
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from SAlisbury, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven was not heating properly
took out the old element after cutting the circuit breaker, put in the new one, it was that easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Gloversville, NY
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned-out six inch electric stove- top burner
Removed the old and slipped in the new.No problem and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Plano, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
botton bake element burned out
Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.
Was this instruction helpful to you?
Thank you for voting!