Models > JBP62BD2CT > Instructions

JBP62BD2CT General Electric Range - Instructions

Jump to:

All Instructions for the JBP62BD2CT

Customer:: Charles from Pittsburgh, PA
Parts Used:: WB30X46987, WB30X46986
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Bake element buned and broken

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

Was this instruction helpful to you?

Customer:: Vicki from Irvine, CA
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Replaced damaged oven rack

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Was this instruction helpful to you?

Customer:: Greg from Chicopee, MA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Socket set

Bake Element burnt out

watched the video on part select - took less time then they said.

Was this instruction helpful to you?

Customer:: DAVID from PARIS, MI
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

the bottom element of the oven was broken

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!

Was this instruction helpful to you?

Customer:: Lori from Bellows Falls, VT
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

heating element blew apart

I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.

Was this instruction helpful to you?

Customer:: Harriet from Jacksonville Beach, FL
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Open door. Put racks in.

nothing to it.

Was this instruction helpful to you?

Customer:: John from Denham Springs, LA
Parts Used:: WB24T10027
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Open Switch

Pull knob. Pull wires. Pull two screws. Replace switch

Was this instruction helpful to you?

Customer:: Greg from Ft. Washington, PA
Parts Used:: WB02K10254
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Was this instruction helpful to you?

Customer:: David from Alice, TX
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Burned out heating element

took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.

Was this instruction helpful to you?

Customer:: Ralph from Redding, CA
Parts Used:: WB23X5340
Difficulty Level:: Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Screw drivers, Socket set

oven continued to get F2, F3 and F5 error messages when ovewn got hot

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

Was this instruction helpful to you?

Customer:: Gary from Port Gibson, MS
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Baking element burned out.

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Was this instruction helpful to you?

Customer:: BILLY from WEBSTER, FL
Parts Used:: WB24T10029
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver

Burner Would Not Turn Off

Replace control switch

Was this instruction helpful to you?

Customer:: Bernadette from Coatesville, PA
Parts Used:: WB30X46987
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

bake element needed to be replaced

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

Was this instruction helpful to you?

Customer:: Raymond from Highland, MI
Parts Used:: WB30X46986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

broiler element burned completely out

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Was this instruction helpful to you?

Customer:: Jerry from Dallas, GA
Parts Used:: WB30X46987
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours

bakinf element not working

best to pull stove out away from wall connect from behind stove

Was this instruction helpful to you?

All Instructions for the JBP62BD2CT