JSS01*04 General Electric Range - Instructions

I first remove the oven door, which is very east on this model. You tilt it a quarter of the way when you open it to use and pull up. It comes off very easy. My second step was pulling on the bake element towards the front. It will expose the wiring connection to the bake element. You will see two wire that are attached by two one screw for each connection. You will need a nut driver to remove. The removal is very simple. Note: Please be sure to turn off your circuit breaker to the oven! ( this is a safety measure,plus it will make you more at ease with the installation. You then can remove the screw nuts & replace with you new bake element. A real piece of cake & very easy even for a average home-owner. Thanks to Part Select for ease of ordering this item. It is a very friendly website! Thanks! Orin

1)Unscrewed the mounting nuts, 2) pulled the heating element out a couple of inches, 3) unscrewed the screws holding the wires in place, 4) removed and tossed the old heating element, 5) placed the new heating element in place, 6) re-screwed the wires to to the element, 7) pushed the heating element back into the wall of the oven, 8) reset the mounting nuts, 9) cleaned up the work area, 10) cranked up the oven and made a pizza. I'm not particularly skilled when it comes to things of this nature, but it was ridiculously easy...

First I turned the power off to the oven at the breaker box. Then I removed the nuts holding the element to the rear wall of the oven and pulled it out a couple of inches. I saw that only 2 nuts held the element to the wires. I found the part on your site very easily and placed my order. The part was at my door 2 days later! I removed the old element, replaced the new element and turned the breakers back on. Repair complete!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...removed the baking element and put the new element back in the same way I took the old one out. It was great directions that was posted and easy to do. Best of all I saved the price of a service call. Thank you

First I turned off the power to the stove,removed oven racks,removed the two screws that held the element in place,pulled unit out a couple inches ,removed the two screws that held the wires in place ,removed element.
Placed new unit where old one went and placed wires in proper order and put together and placed back . turned power back on and WALAA......nothing......apparently that wasnt the problem....Husband baught me a new stove,after 35 years why not.

Unplugged oven, removed 2 screws that hold the element in place. Pulled element to expose wires. Disconnected wires & removed old element. Reversed removal for installation, plugged in and worked great.

Two screws to remove the element and two screws for the wire connectors and it was done.

First, I turned off the circuit breaker. Then I removed the two screws on the hinged plate that attaches the element to the back wall of the oven. Then pulled out the two wires attached to the element by screws. I detached the old element and reversed the sequence to install the new element. Very simple operation for the average homeowner.

1) turned off breaker to oven
2) removed oven racks
3) removed screws holding old element
4) pulled out element far enough to remove 2 wires attached to old element
5) noted colors, left white, right black
6) attached new element to wires
7) attached new element to oven
8) put back oven racks
9) turn breaker back on
10) test oven
done
EASY!!

order process went very well - easy to do

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, and reconnected the two wires back with the new screws. Reinstalled the element by reassemblyinig the two screws holding it in place.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Ordered the part online, received it in a coupledays and my son-in-law installed it in a flash. The cost was very reasonable also. The whole experience was a snap. Thanks so much!

This job was easy. I removed two screws to release the element from the back of the oven, two more screws to release the electrical connection, connected the new element with the new screws provided and reattaced the heating element to the back of the over. It took two tries to get the element so that is sat level at the bottom of the oven. Ten minutes later, I was making dinner!

The bake element is very easy to replace. Turn off the circuit breaker to the stove. Two screws (1/4" socket needed, not screwdriver) come out to release the plate, then two more screws of the same size to unfasten the element to the stove wiring. Reverse the process to put the new one back in. I let my fourteen year old son do the whole thing. By the way, the photo of the element on the web site did not look like the element in my stove. I called customer support and was assured that it was the proper part. When it arrived, it did exactly match my element. The photo on the web site was incorrect. (Part number PS249466)