JMP31WV1WW General Electric Range - Instructions

After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pushed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe

I am 68 years old and found that changing element was a breeze---using pliers removed nuts--unhooked bad element--rehooked new element---done------------recieved new element in 2 days--------- Thanks -----------------

I cut of electric braker in fuse box, unscrewed two screws and replaced element in less than five minutes, really easy task. Oven worked well. Thank you Park Select, good job.

I simply removed the two screws but the back of the element holding it in place and pulled the element out far enough to clearly see the wiring. (TURN OFF THE ELECTRICTY TO THE OVEN). Gently pull the snap connectors off the element leads and snap them on the replacement element, push wiring back into oven opening, tighten down screws, clean up and close the door. Turn electricty back on and start the oven. It will smell for a few moinutes while the element heats up for the first time. You are good to go. To Easy

I thought because the broiler was off that I could remove the element with not problem. As I was pulling the element out, it sparked, melting something in the back I couldn't see at the time. I immediately went to the breaker box and turned the power to the oven off. After I found the website online I was very gratified to see how easy it was to identify the element I needed and order it. I removed the old element. One of the wires from the element slipped through the hole in the back of the oven. To get at it I had to unscrew the four screws around the outside edge of the oven and pull the whole oven out. I had a table handy that I pulled up next to the oven and set it on without disconnecting the main wiring. After getting the oven out I removed the six or so screws on the coverplate and easily found the loose wire. I pushed the wire back through the hole in the back of the oven and made sure it would not fall back into the hole. I put the back plate on with all its screws; pushed the oven back into its hole and screwed the four screws in around the edge that hold the oven in. Then I attatched the broiler element to the spade connectors and screwed it back in place. I turned the breaker switch back on and tested it. It works.

I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.

After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worked once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.

Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.

I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.

ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.

I removed the two screws holding the element in, pulled it out, and unplugged it. Installation was reverse of removal. It's just that simple.

changed element

The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.