JGBC20WEA2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- clare from north brunswick, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burner assembly could no longer be cleaned
pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Locust Valley, NY
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven handle broke off
Couple of screws and it was done. Simple and inexpensive since I thought I was going to have to buy a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Franklin, NC
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the stove top burners had burned all the way through
matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warwick, RI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
The key here was that I found the correcd part for an older kenmore oven and it was easily installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alphonse from Glendale, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We had to buy two dubble burner assemblies because one burner was out on each old assembley
The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Forestville, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The double burner assembly had years of gunk so the burn was not clean.
The old double burners lifted off. Before the new burner could be set down into place, the area had to be completely cleaned using a flat blade screwdriver and damp rag. This allowed the new burners to seat properly in place. That is it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Omaha, NE
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Orignal oven door handle had multiple fractures and was fast becoming useless.
Removed the old handle with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Payson, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were not burning properly
Just removed the old and set in the new. Waalaa. All is well now. The web site, ordering, shipping and all was super easy.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from La Veta, CO
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Back burner not working
Lift stove top, rest it on the pop out holders on stove.
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sumiko from Plano, IL
- Parts Used:
- WB31K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wanted to give stove a newer look and I did
The stove in my kitchen is fairly new but it was installed when this duplex was a rental property. This range came perfectly clean except the burner grates. So I found PartSelect online and it was soooo... easy. Partselect made it crazy easy to find the part and order it. And they shipped it within a week of ordering. 3 of the grates were backed ordered and they still arrived within the week. It was a great experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Houston, TX
- Parts Used:
- WB31K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A Cover Dish From The Micowave Was Put On A Hot Burner
Tried to srub the melted plastic from burners. Decided that 9 years old but it was a toxix plastic chemical and that even if one piece was left somewhere on the grate that this would not be healthy for the family. Just replaced the two grates. Easy on easy off. Much cheaper than general electric. The shipping was fast. The operator was very easy to place the order. In the horizon there are plans to get 2 more grates so there is a match. Highly recommend this move for repair. Before I had placed the order I had asked for advice from the lady with the company just to get a second opinion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Birgit from Opelousas, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Burlington, OK
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Would Not Turn Off
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me. . . . . . 25 Seconds or so and it went out. . . . . Job done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from West Roxbury, MA
- Parts Used:
- WB03K10036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Numbers removed from knob when cleaned
After receiving the new knob and installing by pulling off the old one and with a little pressure applied, I just pushed the new one into place. With the new knob installed I turned the oven to 350 degrees' putting an oven thermometer into the oven and waited for it to turn off at the end of the pre heat, then matched the knob temp with the thermometer by pulled the handle back off and with the two small screws on back side of handle loosened I adjusted the handle to match the over temperature tighten screws reinstalled
Was this instruction helpful to you?
Thank you for voting!