JGBC20BEH2WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- candace from RALEIGH, NC
- Parts Used:
- WB15K10046
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
OLD HANDLE TWO PIECE MODEL FELL APART
REMOVE TWO TORX HEAD SCREWS AT TOP OF INNER DOOR
PANEL. THEN REMOVE TWO ALIGNMENT SLEEVES THAT WERE
HELD WITH SHEET METAL SCREWS AND DISCARD BOTH THE SCREWS (SHEET METAL) AND THE SLEEVES. ALIGN TWO SMALL PINS ON EITHER SIDE OF OUTER DOOR PANEL AND ATTACH WITH THE TORX HEAD SCREWS(MAY WANT TO USE A DRILL IF YOU HAVE THE CORRECT TORX BIT). NEW HANDLE ONE PIECE BETTER DESIGN... WIFE LOVES IT.
PANEL. THEN REMOVE TWO ALIGNMENT SLEEVES THAT WERE
HELD WITH SHEET METAL SCREWS AND DISCARD BOTH THE SCREWS (SHEET METAL) AND THE SLEEVES. ALIGN TWO SMALL PINS ON EITHER SIDE OF OUTER DOOR PANEL AND ATTACH WITH THE TORX HEAD SCREWS(MAY WANT TO USE A DRILL IF YOU HAVE THE CORRECT TORX BIT). NEW HANDLE ONE PIECE BETTER DESIGN... WIFE LOVES IT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from NORTH BANGOR, NY
- Parts Used:
- WB16K10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Old burner bake tube was burned out in 1 spot.
New bake tube fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from CHICAGO, IL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Existing oven bottom was damaged.
Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from AVOCA, IA
- Parts Used:
- WB27T10469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Digital clock no longer worked
No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Giddings, TX
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner was old and needed replacing
Took it out of the box, lifted the stove lid and replaced the part, no tools required. Very satisfied with the shipping and the part, great service. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERNEST from MANCHESTER, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from NAPLES, FL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom badly marred after 16 years.
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from MUNDELEIN, IL
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners were old and dirty
Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherri from MORGANTOWN, WV
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner could not be cleaned any more.
Just lifted off the old burners set on the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from ONTARIO, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One burner went out
All I did was remove the old burner and put the other one on. Took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenora from Crowley, TX
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Screws fell into a black hole and trouble threading the thermostate
My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.
Was this instruction helpful to you?
Thank you for voting!