JMP28GR1AD General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Alpine, NJ
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
broiler element broken -- rotted
First I removed the two screws that hold the element in place. I then pulled the element out disconnected the two wires. THE PROBLEM IS THAT THERE IS HARDLY ANY WIRE TO WORK WITH. Otherwise I would have been finished in ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hollis from Clarksville, MD
- Parts Used:
- WB44K5013
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
The broil element broke.
We removed the two very tiny screws that held the plate through which the element was connected to the wiring. It was extremely difficult to do so, because the screws were so tiny. Our socket set did not have such a small attachment, and we had to use an adjustable wrench. Once we accomplished that, we unhooked the old broil element from the wires. At that point, the wires snapped back into the wall. There was almost no slack to pull the wires back out into the oven so that we could hook the new broil element up. It took more than an hour of maneuvering before we were able to get hold of enough of the wires so that we could grab onto each one and hook up the new broil element. One we did that, it was easy to place the broil element back into its brackets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from great neck, NY
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
a segment of the broil element took on fire
it was real easy, I just watched my husband do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HOUSTON, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from poughquag, NY
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnrd -out heating elements
Turned AC off. Removed bracket screws and pulled out ac connections. Removed old element and reilstalled new element and set AC on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Indianapolis, IN
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Heating element broke
First turn circuit breaker off. Remove two retaining screws, disconnect two connectors at the end of the element, toss old element and reverse the procedure
to install.
to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Mayfield, NY
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The broiler element burned out in the oven.
As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman
Thanks,
Ken Fuelleman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from keller, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Corinth, MS
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake burned out, checked open with an ohm meter
removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Centreville, VA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Short circuited/burned out upper bake element
This is a simple repair of the PS249249 UPPER BAKE ELEMENT requiring only a 1/4 in nut driver or socket wrench.
1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.
Make sure not to remove any insulation.
1. unplug the old element after removing the two screws holding the element in place.
2. Insert the new element in the electrical receptacle and reinsert the screws to secure the new element.
Make sure not to remove any insulation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Pierson, MI
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bake element burned out
My husband (a retired tool & die maker) easily removed the old bake element after first turning off the circuit. He cleaned up the burned salt that we had used to try to put the "fire" out but finally just shut down the circuit. Then just as easily istalled the new element. Thanks to your quick service, we were only without the use of the oven for a day and a half!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elwood from Allen, MD
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I researched the part number from partselect.com, ordered it and in less than a week (even in all the snow!) I had my part. Fifteen minutes later, my wife was broiling dinner! I repaired my broiler element without waiting on a repairman and for less than $50.00!
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Glassboro, NJ
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element feet broke off and element was laying against botom of oven.
Turned off the power at the panel and then simply removed the two hext screws and unplugged the old element. Plugged in the new element and used a nut driver to relpace the two screws.
Was this instruction helpful to you?
Thank you for voting!
Oven elements were not heating properly.
I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
Was this instruction helpful to you?
Thank you for voting!