PS905SP3SS General Electric Range - Instructions

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Really easy. Part came in rapid time and was the right part. Went on web and got instructions with video how to install.

This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.

I ordered the wrong part, and your helpful staff directed me to call the manufacture for the part number (they even proved the tele number). The part was several dollars cheaper at your site. I now have all the knobs to use my stove!! thanks.

Easy

Followed example on YouTube! Very easy.

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

I got someone to look at the stove. They told me what I needed. I looked all over the Internet and couldn't find the part. One guy told me just to buy a new stove top because mine was an antique. It still looked good and two burners were still working. I didn't give up. I found the part on partselect bsite and was thrilled. It shipped fast and was exactly the right part. Now my stove works like new.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Easy to install replacement parts using the screws provided.

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Turned off the power at the breaker. Then I lifted the cooktop by pressing up from the bottom, while my wife slid two boards over the recess. I lowered the cooktop onto the boards, removed 12 screws around the perimeter of the case and carefully lifted the glass top and placed it on a towel on the DR table. (remove the control knobs first) removed the wires leading to the infinite control, marking which color when where, removed the two screws holding the infinite control, and replaced the old with the new. Reattached the wires, replaced the cooktop, replaced the screws, held it up while my wife removed the boards and then carefully lowered the cooktop into the recess. Attached the knobs, flipped the breaker back on and turned control to hi. It worked!