All Installation Instructions for General Electric Range PB905TT2WW

Customer:: lynn from sunnyside, NY
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

F2 reading

Followed the instructions that were sent to me by E-Mail.

Was this instruction helpful to you?

Customer:: Thomas from Albuquerque, NM
Parts Used:: WB02T10017
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Convection fan came loose from shaft

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Was this instruction helpful to you?

Customer:: Mario from Deer Park, WA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Was this instruction helpful to you?

Customer:: Richard from Newark, DE
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Range lower drawer would not stay on track.

Easy to install replacement parts using the screws provided.

Was this instruction helpful to you?

Customer:: jud from gatesville, TX
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

F2 error code

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Was this instruction helpful to you?

Customer:: Kathleen from Munt Laurel, NJ
Parts Used:: WB20T10024
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Oven Probe broke

Ordered new probe

Was this instruction helpful to you?

Customer:: Gerald from Philadelphia, PA
Parts Used:: WB30T10129
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner not operational.

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Was this instruction helpful to you?

Customer:: Kenneth from Salem, OR
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Flashing F2 and erratic temperature readings.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Was this instruction helpful to you?

Customer:: Robert from Woodinville, WA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Our bottom drawer support broke and the bottom drawer was canted

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Was this instruction helpful to you?

Customer:: Edwin from HIGHLANDS RANCH, CO
Parts Used:: WB30T10133
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

one burner not working

Removed two screws to access burner. Removed three power clips from burner, reattached the clips to new burner, removed brace clips and attach to new burner, close lid and reattach stove cover.

Was this instruction helpful to you?

Customer:: Steven from Lansdale, PA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Hard to move drawer in and out because the rear drawer supports broke off.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Was this instruction helpful to you?

Customer:: Robert from Estero, FL
Parts Used:: WB24T10058
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers, Screw drivers

Dual burner on range stopped working.

Changed out the burner with a new replacement and it still didn't work. The socket on the old burner had a burn mark on it. The infinite switch operated sloppy not crisp like the other burners.Ordered a replacement online. Moved the range away from wall and cabinet and shut off electric at panel box. Removed upper back panel. removed switch knob and 2 screws holding switch. Compared electrical connections of both switches and saw that they were different. Read instructions which were included with new switch and found diagram for connecting old lead to new lead correctly. After all leads were connected, remounted new switch powered up and tested OK.

Was this instruction helpful to you?

PB905TT2WW General Electric Range - Instructions