PB905TT1WW General Electric Range - Instructions

Used the schematic on the website to order part and disassemble/reassemble with new fan motor. Works like new.

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

First I found a u-tube video on how to repair this. I found the model number of my stove and used my phone to take a picture of it. I found the part on part select.com and ordered it. It came within a few days.
Turn off electricity to the stove. There were two screws to loosen and allow me to lift the glass stove top. It did not come off and we made a stick to hold it open. Then we unplugged and removed the old burner paying attention what was plug in where, maybe 4 plug ins. Then we clipped it back in, closed the top, rescrewed the top on. Turned on the electricity. It took 10 minutes to replace. Very easy!

Ordered the part, it arrived and 5 minutes later it a complete installation

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Remove old stained gasket and replaced with new. Only $57.00!

Removed the two sheet metal screws securing the range top after disconnecting the power. Removed the mounting clips to the old range element and installed the new one. It was an easy fix.

replaced Plastic Guides

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

removed 2 screws that hold the cover in place, inserted the new panel at the bottom, pushed top in place and reapplied the 2 screws.