P2S975DEP3WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Knob Noster, MO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken rear drawer support
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry L from Puyallup, WA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Glen Allen, VA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Erratic oven temp
RE: 2 yr. old GE double wall oven with convection option in upper oven, non-convection in lower oven: baked goods were not browning, were undercooked or burned. Tested both ovens on regular bake setting using 2 oven thermometers. Set ovens for 350. Although after 10 min both ovens beeped "ready", the oven thermometers actually read 200 - then would swing up as high as 500 and as low as 200 during the 20 min test period. Decided to first replace top oven sensor only, just in case it really was a more expensive control panel problem. It was a bit awkward to reach back there with the oven door in the way, but I have long arms! Aimed my flashlight, removed nuts with a socket wrench, pulled out the sensor, popped the clip and the old sensor easily separated from its connection. Snapped on the new sensor, pushed it back in and reset the nuts. Easy. Set the oven for 350 and tested again with 2 oven thermometers for 45 min. Voila! The oven thermometers read exactly 350 when the oven beeped "ready" and it stayed at 350 throughout the entire 45 min retest period with only a 3 degree variation both up and down. What a great improvement! Immediately went online to Parts Select and ordered another sensor for the bottom oven which was having the same problem. Fixed both ovens all for under $30 - and just in time for Christmas cookies! Don't want to know what the repair guy would have charged.......Merry Christmas!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dock from Aurora, CO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICK from Vernon, CA
- Parts Used:
- WB48T10068
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic guide Broken
replaced Plastic Guides
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HENDERSONVLLE, NC
- Parts Used:
- WB02T10461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Murrells Inlet, SC
- Parts Used:
- WB04T10050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door gasket was soiled
took out old gasket and inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FAIRFIELD, OH
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
- works great. tested it....snaps in, reads correctly, snaps out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Glencoe, NM
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Remove back panel or access sensor, replace sensor and panel
Removed back panel, change out sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Zachary, LA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake and convection cycles quit working after a10 minutes
Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!