All Installation Instructions for General Electric Range P2B930SET2SS

Customer:: Stephen from North Las Vegas, NV
Parts Used:: WB16K10070, WB16K10055, WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

carbonized burners

Replaced all four

Was this instruction helpful to you?

Customer:: Thomas from Hamilton, VA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Old bake element burned out

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

Was this instruction helpful to you?

Customer:: John from Los Angeles, CA
Parts Used:: WB16K10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Was this instruction helpful to you?

Customer:: Stephen from East Williston, NY
Parts Used:: WB16K10062, WB28K10222
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burner cap did not fit burner, causing ignition failure

Replaced burner. New burner now ignites properly.

Was this instruction helpful to you?

Customer:: John R from Asheville, NC
Parts Used:: WB20T10024
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

missing meat thermistor

plug in thermistor when needed

Was this instruction helpful to you?

Customer:: glen from felch, MI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Was this instruction helpful to you?

Customer:: Marcus from Lagrange, GA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Broken bake element

Very easy to install save several dollars

Was this instruction helpful to you?

Customer:: Greg from Ft. Washington, PA
Parts Used:: WB02K10254
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Was this instruction helpful to you?

Customer:: William from Franklin, TN
Parts Used:: WB30X46986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Element was burned out

Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!

Was this instruction helpful to you?

Customer:: richard from Palm Coast, FL
Parts Used:: WB30X46986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

Total Burn Out Of Original Broiler Element

Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.

Was this instruction helpful to you?

Customer:: Rodney from Chambersburg, PA
Parts Used:: WB30X46987
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Bake element not working

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Was this instruction helpful to you?

Customer:: don from protection, KS
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

element burnt out

ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking

Was this instruction helpful to you?

Customer:: Thomas from Rogersville, TN
Parts Used:: WB30X46987
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Oven would not reach bake temp.

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

Was this instruction helpful to you?

Customer:: Gary from Port Gibson, MS
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Baking element burned out.

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Was this instruction helpful to you?

Customer:: Raymond from Highland, MI
Parts Used:: WB30X46986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

broiler element burned completely out

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Was this instruction helpful to you?

P2B930SET2SS General Electric Range - Instructions