All Installation Instructions for General Electric Range P2B930DET3BB

Customer:: Stephen from East Williston, NY
Parts Used:: WB16K10062, WB28K10222
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burner cap did not fit burner, causing ignition failure

Replaced burner. New burner now ignites properly.

Was this instruction helpful to you?

Customer:: Marcus from Lagrange, GA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Broken bake element

Very easy to install save several dollars

Was this instruction helpful to you?

Customer:: Greg from Ft. Washington, PA
Parts Used:: WB02K10254
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Was this instruction helpful to you?

Customer:: John R from Asheville, NC
Parts Used:: WB20T10024
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

missing meat thermistor

plug in thermistor when needed

Was this instruction helpful to you?

Customer:: henry from ridgewood, NJ
Parts Used:: WB29K10024, WB29K10023, WB29K10022, WB28K10222
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burner caps chipped

remove old, install new

Was this instruction helpful to you?

Customer:: Lesley from LaPlace, LA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Bake Element Broke

followed the instruction from your video an it was a snap

Was this instruction helpful to you?

Customer:: glen from felch, MI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Was this instruction helpful to you?

Customer:: richard from Palm Coast, FL
Parts Used:: WB30X46986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

Total Burn Out Of Original Broiler Element

Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.

Was this instruction helpful to you?

Customer:: don from protection, KS
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

element burnt out

ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking

Was this instruction helpful to you?

Customer:: William from Franklin, TN
Parts Used:: WB30X46986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Element was burned out

Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!

Was this instruction helpful to you?

Customer:: Michael from Hamden, CT
Parts Used:: WB30X46987
Difficulty Level:: Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers

Wires to attach to bake element retracted into stove body

I had to remove the back panel on the stove to free up taped wires to get more length.

Was this instruction helpful to you?

Customer:: Rodney from Chambersburg, PA
Parts Used:: WB30X46987
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Bake element not working

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Was this instruction helpful to you?

Customer:: Thomas from Rogersville, TN
Parts Used:: WB30X46987
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Oven would not reach bake temp.

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

Was this instruction helpful to you?

Customer:: Thomas from Albuquerque, NM
Parts Used:: WB02T10017
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Convection fan came loose from shaft

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Was this instruction helpful to you?

Customer:: Charles from Pittsburgh, PA
Parts Used:: WB30X46987, WB30X46986
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Bake element buned and broken

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

Was this instruction helpful to you?

P2B930DET3BB General Electric Range - Instructions