Models > P2B930DET1BB > Instructions

P2B930DET1BB General Electric Range - Instructions

Jump to:

All Instructions for the P2B930DET1BB

Customer:: Ralph from Redding, CA
Parts Used:: WB23X5340
Difficulty Level:: Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Screw drivers, Socket set

oven continued to get F2, F3 and F5 error messages when ovewn got hot

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

Was this instruction helpful to you?

Customer:: Jerry from Dallas, GA
Parts Used:: WB30X46987
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours

bakinf element not working

best to pull stove out away from wall connect from behind stove

Was this instruction helpful to you?

Customer:: Anne Marie from Andover, MA
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Was this instruction helpful to you?

Customer:: Lesley from LaPlace, LA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Bake Element Broke

followed the instruction from your video an it was a snap

Was this instruction helpful to you?

Customer:: Harriet from Jacksonville Beach, FL
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Open door. Put racks in.

nothing to it.

Was this instruction helpful to you?

Customer:: Stephen from North Las Vegas, NV
Parts Used:: WB16K10070, WB16K10055, WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

carbonized burners

Replaced all four

Was this instruction helpful to you?

Customer:: glen from felch, MI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Was this instruction helpful to you?

Customer:: Marcus from Lagrange, GA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Broken bake element

Very easy to install save several dollars

Was this instruction helpful to you?

Customer:: Greg from Ft. Washington, PA
Parts Used:: WB02K10254
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Was this instruction helpful to you?

Customer:: henry from ridgewood, NJ
Parts Used:: WB29K10024, WB29K10023, WB29K10022, WB28K10222
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burner caps chipped

remove old, install new

Was this instruction helpful to you?

Customer:: Thomas from Hamilton, VA
Parts Used:: WB30X46987
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Old bake element burned out

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

Was this instruction helpful to you?

Customer:: John from Los Angeles, CA
Parts Used:: WB16K10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Was this instruction helpful to you?

Customer:: Johnette from Baltimore, MD
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

no racks to oven

Easily glide in.

Was this instruction helpful to you?

Customer:: Arthur from Riverside, RI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Hot Spot On Burner

Replaced old burner element with new, easy

Was this instruction helpful to you?

Customer:: Tien from Lawrence, MA
Parts Used:: WB29K10024, WB28K10222
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

the cap is crack

I order this parts only take me 5 second to install i realy love love this parts i recommen to people to order you are the best

Was this instruction helpful to you?

All Instructions for the P2B930DET1BB