JGBS07DET3WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brenda from Franklin, NC
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the stove top burners had burned all the way through
matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clare from north brunswick, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burner assembly could no longer be cleaned
pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warwick, RI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
The key here was that I found the correcd part for an older kenmore oven and it was easily installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alphonse from Glendale, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We had to buy two dubble burner assemblies because one burner was out on each old assembley
The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Forestville, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The double burner assembly had years of gunk so the burn was not clean.
The old double burners lifted off. Before the new burner could be set down into place, the area had to be completely cleaned using a flat blade screwdriver and damp rag. This allowed the new burners to seat properly in place. That is it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Payson, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were not burning properly
Just removed the old and set in the new. Waalaa. All is well now. The web site, ordering, shipping and all was super easy.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from La Veta, CO
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Back burner not working
Lift stove top, rest it on the pop out holders on stove.
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL R. from BOSTON, MA
- Parts Used:
- WB18X26988
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Surface burner not igniting
I ordered the part I needed I recirived it overnite by 9 am.
I installed it in 20 min iwould have taken 5 min but the part was of such high quality I had to use a drill to make the opening slightly larger, very easy.the part I received was twice the quality of the original part. Thank You
I installed it in 20 min iwould have taken 5 min but the part was of such high quality I had to use a drill to make the opening slightly larger, very easy.the part I received was twice the quality of the original part. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Aldan, PA
- Parts Used:
- WB35K10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old bottom oven was really crusted and way too hard to clean.
Removed oven door.Opened slightly and lifted off.Removed two screws from rear of oven bottom.Lifted out bottom oven.Reversed for installing new bottom. Looks great.And the price was well worthit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela S from Chesterland, OH
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven Heating Too Hot, More Than 100 Degree Beyond Setting
Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Birgit from Opelousas, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia A from Newport, NH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gas flame flared and blackened pots; gas jets clogged
raised the range top so the supports locked in place. carefully lifted off the old burner assemblies. used a paper towel to remove any black soot from gas jets. opened the plastic package of the new burner assemblies, pulled out the new parts and carefully put them in place. turned on the flame to test... took less than 5 minutes to fix a problem that's been annoying for 3 years!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cincinnati, OH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
3 of 4 Burners would not light
Open the stove top pulled old burners out dropped new set in place. Theyclick right in NO TOOLS REQUIRED!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!