JGBP25DEMBWW General Electric Range - Instructions

Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!

removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!

Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.

replaced the ignitor and it has worked perfectly the last week - Service repair walked away from the service call stating it was too random - you website state 91% cause, you were correct I wish I had done this 2 years ago

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.

Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.

My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.

thank you

removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.