JGB500SEP4SS General Electric Range - Instructions

I removed the oven door, the base panel of the oven and slid out the broiler tray. Next, I pulled the wires out of the access hole in the back of the oven, then diconnected the modular plug and removed the 2 screws fastening the ignitor. I tested the ignitor with my ohm meter and found out that it did not have the necessary zero ohms resistance. The meter indicated an open circuit, so I ordered the replacement part, which was delivered in less than 24 hours. Then I reassembled everything and tried the oven. Works like new again.

removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.

At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.

I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners requires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....

I have requested this part with the original p/n WB03K10303 and
p/n AP396896. Each times I received a different part than part I ordered. Has this parts been revised? The shaft of the knob is to to small
to to slide over burner controller stem.

I removed the two screws that hold the element in place then I had to splice the wires because the connector was not right and used the two wire nuts that came with the unit .

Just plowing in one by one

I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.

This is a wall mounted oven. Quickly removed the door off hinges (no tools needed). Removed two mounting philips head screws from old igniter. Pulled on wires from the old igniter from back of oven to expose connectors. Disconnected the old igniter. Because the new igniter had a different type of connector, I had to cut connectors off the oven wires as well as the new igniter and use the provided wire nuts. I stuffed the wires back into the back wall of the oven and repositioned the insulation, secured the new igniter and put the door back on. Job done, oven works fine.

Just remove the other knobs and replace with new ones

Over a duration the oven burner would take time to light, then eventually not ignite at all, so repaired ignitor and alls good. Easy, easy, didn't have to disconnect gas, electric for safety.

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM