JGB250GET2SA General Electric Range - Instructions

First I unplugged the stove. I gently removed the two screws that hold the old element in place. I snipped the wires and then twisted the new wires with the stove wires and placed caps on wires. GENTLY replaced new element with screws. DO NOT OVER TIGHTEN. Then I tested the oven after I put it back together and the oven works perfectly.

Easy

The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!

Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.

take off top grates,place new one's in time 20 sec.

These new pans fit perfectly.

changed double burmer pans

I removed the two screws that hold the element in place then I had to splice the wires because the connector was not right and used the two wire nuts that came with the unit .

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

e-mailed my problem and reply was igniter our gas valve took a gamble and ordered the igniter. easy fix. two srews and plug in wires.

removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.

The repair went easy the tube was a perfect fit

At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.

replace igniter

oven and stove top burners worked fine, but broiler would not light. diagnosed problem as bad igniter. ordered parts on line and received them next day with regular shipping!

removed oven door and bake racks. removed old igniter and snipped wires.

installed new igniter and used ceramic wire nuts to attach wire leads.

reinstalled door and racks.

works fine. who knew home repairs could be so easy and fun!