JBS60DF1WW General Electric Range - Instructions

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Isolated to control switch.

Replaced

Replace control switch

Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!

Self-clean the oven or use Easy-Off. Lay some towels or other padded ragging on the kitchen table. Open the oven door and lock the hinges. Pull the door out of the oven and lay it on the table with the oven handle hanging off the edge of the table. The inside of the oven door will be face up on the table. Use the 1/4 Nut Driver to remove three sheet metal screws from the bottom of the door. Use the T10 to remove two long screws from the top inside of the door. lift the door guts and set aside along with the 5 screws and two spacers you found under the top of the door. Use the nut driver to remove 4 screws holding the Door Bottom Channel Trim. The door handle and side channels will fall off (catch and set aside). you are left with one piece of glass with the old bottom channel trim. Gently tap the lip of the channel with a screwdriver in a towel to slip it off the glass. Gentle patience is a virtue here or the glass will break. Clean the glass with CeramaBryte or equal to get the burnt oven goop off. (While you're at it, do the same to the bottom of the door guts above.) Slip the new bottom channel on the glass as far as it will go (not very far in my case) and replace the door handle and side channels. You will see that the holes line up pretty well without having to jam the bottom channel onto the glass. Screw (4) the side channels to the bottom channel. Replace the Door Guts, being careful to line up the two spacers at the top of the door. Three screws in the bottom of the door, then the two Torx screws back in the top of the door. Put each screw in just finger tight and after they are all started, screw them home. Slip the reassembled door back in the oven frame, flip the locks up and Voila! Now that it's over, let me just say that if a camel is a horse designed by a committee, this thing must have been thought up by the US Congress!

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Purchased the board installed it and saved about 130 dollars.

Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

This repair is really easy unless the trim piece has rusted so badly that it's attached itself to the front door glass. It took a long time and some WD-40 to pry the trim off w/o breaking the glass. REPAIR: Remove the door and lay it on a flat surface. Unscrew the 3 bottom screws w/ small pliers, then unscrew the top two inside door screws w/ a small metric allen wrench. Remove the door trim to get to the last four side trim screws. Once the old trim is out just clean up any residue/rust remaining on the glass, install the new trim and reverse the steps to put the door back together. If the old trim comes off easily it should only take @ 20-30 minutes.