JB690DIF1WW General Electric Range - Instructions

First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!

This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.

Remove the old oven latch and replaced it with the new replacement part. It was very easy to remove and replace with just a few nuts removed

replaced Plastic Guides

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Followed example on YouTube! Very easy.

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Isolated to control switch.

Replaced

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.

This repair is really easy unless the trim piece has rusted so badly that it's attached itself to the front door glass. It took a long time and some WD-40 to pry the trim off w/o breaking the glass. REPAIR: Remove the door and lay it on a flat surface. Unscrew the 3 bottom screws w/ small pliers, then unscrew the top two inside door screws w/ a small metric allen wrench. Remove the door trim to get to the last four side trim screws. Once the old trim is out just clean up any residue/rust remaining on the glass, install the new trim and reverse the steps to put the door back together. If the old trim comes off easily it should only take @ 20-30 minutes.