JB650DF1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sherry from SAINT PAUL, MN
- Parts Used:
- WB56T10105
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Replaced cracked inner oven door glass
This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ALPENA, MI
- Parts Used:
- WB02T10037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The light socket cup could no longer hold the bracket that holds the light cover in place.
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from FREMONT, NE
- Parts Used:
- WB24T10153
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Knob stem broke off.
Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Buckeye, AZ
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Homosassa, FL
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven will not heat
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CONCORD, MA
- Parts Used:
- WB30T10133
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element burned out
Followed example on YouTube! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Loveland, CO
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
fried oven control using raid
replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Paris, TN
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
F2 error when oven was heating up, along with a beeping noise and then it shut off
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from townshend, VT
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was not getting up to temp
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryan from cocoa, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from valentines, VA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
eye wouldnt come on
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Greensboro, GA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner not heating.
Isolated to control switch.
Replaced
Replaced
Was this instruction helpful to you?
Thank you for voting!