JB640DIR6BB General Electric Range - Instructions

Very easy to fix with two people and works great

Unplugged the stove, removed the back control cover, removed the Element Control Knob on front, removed the two screws holding the control in place, pull one wire of old control and connected to the new control - one at a time to ensure proper placement, re-attached the screws, control knob, back cover, plugged in stove, and repairs were completed in less then 15 minutes for both controls.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Identified part and part # using schematic found on GE website, contacted PartSelect and confirmed part number, ordered and paid for part. Two days later I recieved part. Unplugged stove, removed two screws on bottom side of front panel and two on top back of same panel, pulled panel forward, pulled the control knob off, removed two small screws that hold the control switch in place, situated new control switch next to bad switch and removed one wire at the time from the bad switch and connected to the same terminal on the new switch. Put everything back together and Bingo, works like a new one. Thanks PartSelect for the friendly, personal phone service, the fast shipment and competitive pricing on my part.

remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

replaced insulation

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

I found a video on Youtube with a similar circuit board repair and decided that I could probably do it. First and most important is to be certain the range is disconnected from its electric circuit. I did this by turning off the breaker at the electrical panel and then unplugging the range. Second, I removed a panel (four screws) on the back of my stove to expose the circuit board, Next I removed the board (four screws) without disconnecting the wiring. Then I removed the flexible plastic covering from the board which has the control button identities on it. This was the most difficult part because the glue was very sticky and I did not want to tear the cover. After removal, I stuck the plastic covering (still sticky) onto the new circuit board and made sure the buttons were in the correct position. Then, I unplugged the wires one at a time from the old circuit board and made sure I plugged them into the new board in the correct position. Finally, I reattached the new board and the back panel on the stove. This repair was easy and no problem for the average "do it yourself" type.

Control unit was easy to remove ,wires color coded-the face plate(key pad) needed to be separated from the old unit. Carefully used a hair dryer to warm the decal. . . Secured the old unit gently in a vise, warmed ( and separated slowly, with a razor blade and thin putty knife(patience). . Once removed, applied to the new unit. . . 5 Stars to partselect for service. . . . Turned a $400 repair into $100 do-it your self. Partselect will be my 1st "go to" from now-on.

This was the second replacement glass I've bought, but I'm unsure if the first one was from PartsSelect or GE directly. It was a couple years ago when I purchased the first one. The first one popped in rather easily. I scraped out the rust and debris that had built up within the lower metal track and then inserted the glass. By pulling upwards on the door handle I had just enough room to pop it into the upper plastic tabs. The second door I bought was harder. I truly feel the second was larger. I tried the original procedure, but there was significantly more glass at the top, and I couldn't push up on the handle to even clear the handle itself. I removed the glass to re-cleaned the lower track, but it was clear of debris, so that wasn't the problem. I had to completely dismantle the outside plastic frame, insert the window and put it back together. It did fit after that, but now the door scrapes at the top ever so slightly when you shut it. Overall I'm very satisfied, since the oven is older now, but looks great again.

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Easy to install replacement parts using the screws provided.

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.