JB640DIR5BB General Electric Range - Instructions

Performed repair using a video for reference.

threw out the old ones and slide in the replacement ones from you.

Watched youtube video. Very easy to replace

Unscrewed the stove top and replaced the element.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

Easy removal of switch and installation of new switch block.

Unpack the new cooktop and set it upside down on a towel or blanket. Unplug the stove & pull it forward from between the counters. Open the oven door and remove the two screws securing the front edge of the cooktop. Lift & tilt the top up until you can unhook the back edge from the pins that hold it. Pull it forward until you can access the two wiring harnesses & the green ground wire. Take a picture of the harnesses & pinch the sides to unclip & remove them. Unscrew the green ground wire and set the screw aside. Flip the cooktop over and take another picture of how the burners are attached to the cooktop. Unscrew the green ground wire & use needle-nosed pliers to carefully remove the clips holding the burners. This is a little tricky - the flat top of the clip has a small tab inserted in a numbered hole in the top of the burner. After removing the clips holding each burner, carefully move the burners onto the underside of the new cooktop. Use the photo you took to reposition the burners on the new cooktop and reattach the clips using the same numbered holes as before. Reattach the green ground wire. Carefully flip the cooktop back over on top of the oven and use the photo you took to reattach the wiring harnesses and green ground wire. Tilt the cooktop as you hook/hang the back edge back onto the pins (this was also a little hard). Reinsert the two screws under the front edge to resecure the cooktop. Plug it back in to the outlet, and push it back between the cabinets.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

Followed the directions!

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.