JB400SP8SS General Electric Range - Instructions

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

I found a video on Youtube with a similar circuit board repair and decided that I could probably do it. First and most important is to be certain the range is disconnected from its electric circuit. I did this by turning off the breaker at the electrical panel and then unplugging the range. Second, I removed a panel (four screws) on the back of my stove to expose the circuit board, Next I removed the board (four screws) without disconnecting the wiring. Then I removed the flexible plastic covering from the board which has the control button identities on it. This was the most difficult part because the glue was very sticky and I did not want to tear the cover. After removal, I stuck the plastic covering (still sticky) onto the new circuit board and made sure the buttons were in the correct position. Then, I unplugged the wires one at a time from the old circuit board and made sure I plugged them into the new board in the correct position. Finally, I reattached the new board and the back panel on the stove. This repair was easy and no problem for the average "do it yourself" type.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Identified part and part # using schematic found on GE website, contacted PartSelect and confirmed part number, ordered and paid for part. Two days later I recieved part. Unplugged stove, removed two screws on bottom side of front panel and two on top back of same panel, pulled panel forward, pulled the control knob off, removed two small screws that hold the control switch in place, situated new control switch next to bad switch and removed one wire at the time from the bad switch and connected to the same terminal on the new switch. Put everything back together and Bingo, works like a new one. Thanks PartSelect for the friendly, personal phone service, the fast shipment and competitive pricing on my part.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Unplugged the stove, removed the back control cover, removed the Element Control Knob on front, removed the two screws holding the control in place, pull one wire of old control and connected to the new control - one at a time to ensure proper placement, re-attached the screws, control knob, back cover, plugged in stove, and repairs were completed in less then 15 minutes for both controls.

remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.

It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.

Purchased the board installed it and saved about 130 dollars.