JB400SP6SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ike from LOGANVILLE, GA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven is off 10 degrees
I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jayne from EAST PEORIA, IL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Needed to replace oven door gasket
Watched youtube video. Very easy to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LORDSBURG, NM
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
No Spin Cycle
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from San Antonio, FL
- Parts Used:
- WB48T10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
previous owner self cleaned and left oven racks in the oven
threw out the old ones and slide in the replacement ones from you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from ELIZABETHTON, TN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would shut down while baking. Stove top would work.
Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from JOHNSONVILLE, SC
- Parts Used:
- WB30T10133
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Element bad
Since this was the third time I did it all I had to take two screws out to lift the top of stove and replace element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ARROYO GRANDE, CA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The oven did not get up to or hold the correct temperature
This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from HUNTSVILLE, AL
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
When you touched any button on the controls LOC on appeared.
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from HOPEWELL, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Just didn't work no pwr to it
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from BENNETTSVILLE, SC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven could not be turned off once settings were turned on except by unplugging hookup.
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from FARMINGVILLE, NY
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Incorrect oven temperature due to defective temperature sensor.
Performed repair using a video for reference.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Crumpler, NC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven temp wouldn't regulate.
Followed the directions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Goldsboro, NC
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven drawer open and close incorrectly
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICKEY from MONTROSE, NY
- Parts Used:
- WB25T10041
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lens snapped off on the inside-plug was left loose
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dock from Aurora, CO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this instruction helpful to you?
Thank you for voting!