AGBS300EP4BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rudy from Waterloo, IA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Thermostat knob broke off
Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Burlington, OK
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Would Not Turn Off
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me. . . . . . 25 Seconds or so and it went out. . . . . Job done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Geneseo, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gracie from New Orleans, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Burners on a gas stove did not work
Ordering from Part Select was very easy. I simply put in the model number of the stove and the replacement needed popped up and explained why I might need this part. Got a professional install because I was not at the location where the repair was needed. Will use Part Select again. The ordering experience was great and delivery was quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Birgit from Opelousas, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHANNA from GERMANTOWN, MD
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
both burners were bad
Just opened the box, removed the 2 old burners and replaced with the 2 shiny new ones. Yeah success! I placed my order for this product and before I knew it, it was at my front door. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia A from Newport, NH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gas flame flared and blackened pots; gas jets clogged
raised the range top so the supports locked in place. carefully lifted off the old burner assemblies. used a paper towel to remove any black soot from gas jets. opened the plastic package of the new burner assemblies, pulled out the new parts and carefully put them in place. turned on the flame to test... took less than 5 minutes to fix a problem that's been annoying for 3 years!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cincinnati, OH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
3 of 4 Burners would not light
Open the stove top pulled old burners out dropped new set in place. Theyclick right in NO TOOLS REQUIRED!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baltimore, MD
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burners were scorched looking
lifted the old burners out and sat the the new ones in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamyra from Friendship, WI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove burners no longer working
Ordered 4 new burners, snapped the old ones out, put the new ones in and my stove works great. Also, I got my parts in 1 day. Very satisfied with my experience with PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charmaine M from York, PA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
right side burns would not light, if they did it wrapped around outside of burner unit
Pulled old burners out, cleaned area, sat new units in place, made sure they were stable(no rocking), put the top down on the stove and all burners light like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norton from Malta, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One burner wouldn't light
Removed old and set inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Elkhart, KS
- Parts Used:
- WB18X26988
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Left side burners would not light.
took off top burner grates,then the cook top,then the burners,then backguard. found the wire to the spark electrode and atempted to pull the terminal off thespark module and broke off the terminal at the spark module. Now I have to replace the spark module. I replaced the spark electrode and had to open up the hole in the top cover so the terminal would go through. Quite a job and not doon yet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph C from Williamsport, IN
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Temperatures were much usually hotter than indicated
First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.
Was this instruction helpful to you?
Thank you for voting!