ZDP30N4H1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NORMAN from THOMSON, GA
- Parts Used:
- WB24X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
old switch would not turn off
remove c clip, remove two wires
install new switch,
replace c clip, replace two wires
test
have a cup of coffee
install new switch,
replace c clip, replace two wires
test
have a cup of coffee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom E. from SANTA CRUZ, CA
- Parts Used:
- WB44X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Outer heating element shorted out, likely due to age and damage from lower rack changing heights over 10 year period of use.
Turned off breaker at electrical panel. Confirmed power to stove was off with multimeter, as I couldn't pull stove out to unplug it without significant hardwood floor protection in place and extra equipment to "slide" the stove out. Removed all racks. Cleaned the inside of the stove. Unscrewed the two screws holding the element to the back wall and pulled the element out from the back wall, revealing the wiring connections. Held the wire on one side with needle nose pliers and slid the element from the wire retaining clip. Attached the new element on that side to the wire retaining clip. Held the wire on the other side with needle nose pliers and removed the other wire retaining clip. Pulled out the old element and placed it on the floor. Installed the other end of the new element into the wire retaining clip. Confirmed they were both securely attached, crimped down a bit on each retaining clip for good measure and pushed the element and wire ends back into the stove body. Installed the two screws and re-installed the racks. Turned on the breaker at the electrical panel. Confirmed that the lights, igniters and over all worked. Done. 15 minutes. Took just as long getting out the tools, turning things off and on and returning tools to the garage than it did to replace the element. Fun part was finding the model number, finding the web site to purchase the element, and waiting a week to get it. But really easy and the stove works again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darren from Redondo Beach, CA
- Parts Used:
- WB24X10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
inability of igniter to shut off
removed cover, removed clip and exchanged part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherry from Raleigh, NC
- Parts Used:
- WB02X11090, WB02X11087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
insert burner is broken
replace insert burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Jacksonville, FL
- Parts Used:
- WB28X10065, WB13X10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Broken gas line & missing cap
Front control panel must be removed but left hanging on wires, remove kick panel at base of stove, locate and remove all screws that attach side of stove (either side) when all screws have been removed from side panel you can lift up about an inch and remove side panel thus giving you access to base of burners and attached gas lines; after replacing gas line i recharged the lines with gas and checked for leakage by using a grill lighter, (no leaks?) i re-installed the side panel, this was the most difficult part of the repair because the side panel must be properly placed and lined up
Was this instruction helpful to you?
Thank you for voting!