LEB131GY1AD General Electric Range - Instructions

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

AMAZING SHIPPING.Ordered on Friday,received saturday WITHOUT NEXT DAY COST.Amazing,worked perfect.

orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.

I went on-line, found Partselect.com, they gave me the part number, showed me a video on the repair details, shipped the part overnight, and within ten minutes of the arrival of the part, I was up and running. EXCELLENT SERVICE! Thanks for saving Christmas at our house!!

You literally saved our Christmas from a disaster! Four days before Christmas our bake element gave out and we discovered it had split. We found you on the Internet, ordered the part, and prayed you would deliver as promised. We received it the next day, as promised, and in time to cook Christmas dinner. It was a snap to install, literally took five minutes. Your service, response time and instructions were perfect. Keep up the good work!

Watched youtube....

This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!

1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.

Watched youtube. Easy and fast!

Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)

After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.

Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.

Al S.

First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done

Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.

Removed old, and replaced with new, heating element! Maybe 10 seconds.

Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.