PGS975SEM2SS General Electric Range - Instructions

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Ordered by phone parts & very pleased with all of transaction.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

remove oven door of course you cut gas and power off first tried to get screws out of igniter the heads broke off had to take cover off to get screws out slide range out of cabinet take back off to unplug igniter then reassemble

I removed the racks, burner cover, then unscrewed the cover for the starter. Had to get the correct ratchet to remove screws. The hardest part was removing two screws that held the igniter in place. Difficult location to get the tool in. They were also hard to put back. After that it was a matter of pulling the igniter out and disconnecting it. You also have to remove the drawer under the oven so you can unplug the stove.

Read the experience of others on this website with the same problem. I knew exactly what to expect and it all went as the dozen previous oven repair experts had said. I can add my name to the list of experts. The two screws attaching the igniter to the bracket twisted off exactly like everyone else experienced. GE really should look at developing a better attachment. My only problem was because my drill was larger than the bottom of the oven. I had to drill the holes on an angle. One of the holes was wallowed out more than the other. I had to use two different size screws and they were more difficult to screw in. Bottom line; I saved money, the oven works, my wife is happy, so I'm happy.

pulled out appl,removed door,racks,lifted oven bottom to remove,removed both oven and broiler ignitors---went to back of appl to remove gas control valve and replaced--used old oven ignitor in broiler(took chance it would work-it did!)installed new ignitor in oven--tested perfectly--point of info if you have an oversize or dancing flame in oven or broiler--remove flame tube and with 1/2 inch open wrench tighten orfice all the way until it stops--don't force or over tighten-- (the air shutter should open all the way)--flame should be about an 1 inch with white tips--adjust as needed-overall repair including adjustments took about an hour-hope this helps--and i'm not a professional repairman

I called Sears Repair to do the work. Glad I did because there's a lot more than just unscrewing screws...had to use the Dremel because the manufacture stripped one of the screws in assembly that was attached to the ignition part that connects to the burner...

Instead of trying to remove ignitor while mounted to burner, I removed burner/ignitor assembly by detaching it from the oven frame and pulling the ignitor/burner assembly out so connector cleared the access hole. Disconnected and removed whole assembly. Then had easy access to the mounting screws. Removed screws by first spraying threads with WD 40 and waiting. Screws were oxidized so they were damaged when backing them out, as were the threaded mounting holes in the burner ignitor bracket. The screws are not sheet metal as noted in other posts, but rather are 10-32 machine screws. I chased the ignitor mounting bracket threads, then remounted the ignitor with 10-32, 3/8's, cap head, stainless bolts with a stainless star washer (available at any ACE hardware or other similar store) -- that way you don't have to tighten up so tight (just snug them up) -- unless you expect an earthquake every other week. The stainless screws helps retard the corrosion brought on by high heat and any moisture that settles on the bolt threads as the system cools and with subsequent starts.

Pull stove forward to access back. Remove center metal panel, 6 screws with 1/4" nut driver. Disconnect igniter connector. Measure resistance, it should be less than 1 ohm. Obtain new igniter. Test new igniter, 0.30 ohms. Remove oven door, see care and cleaning section of owner's manual. Remove burner cover, 2 screws with 1/4" nut driver. Remove two screws holding igniter. Aside: This is the second igniter to be replaced in this stove. The last one was exactly two years ago. Both times a screw snapped. With a small 5" vise grip the leading edge of the screw could be walked out. This time the two screws were replaced with 6-32 x 3/8" hex socket cap screws, split lock washer s under the screw head, and hex nuts holding the igniter in place. Note: All hardware was stainless steel. The burner cover was replaced. Oven door remounted. Igniter connected. Broiler turned on, it ignited. Center metal panel replaced. Stove moved into its nook.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Ordered new probe