PB970TP1WW General Electric Range - Instructions

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Shut off power to oven. Removed upper oven door and cooking racks. Removed 2, 1/4" bolt, pulled element away from oven back wall and unplugged the 2 wires that went into the heating element and removed the element. Reinstalled the new element by plugging in the 2 wires to the element, pushing the wires back through the back of the oven and reinstalled the 2, 1/4" bolts. Reinstalled the cooking racks and oven door. The complete from start to finish time took about 15 minutes.

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Identified part and part # using schematic found on GE website, contacted PartSelect and confirmed part number, ordered and paid for part. Two days later I recieved part. Unplugged stove, removed two screws on bottom side of front panel and two on top back of same panel, pulled panel forward, pulled the control knob off, removed two small screws that hold the control switch in place, situated new control switch next to bad switch and removed one wire at the time from the bad switch and connected to the same terminal on the new switch. Put everything back together and Bingo, works like a new one. Thanks PartSelect for the friendly, personal phone service, the fast shipment and competitive pricing on my part.

turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

I feel like Macho Mom. I called in the repair guy since I was afraid of dealing with the gas. HE repaired one item but could tell I was comfortable fixing things and pointed out that the gasket was brittle and would cause major problems if not replaced. Took longer to order the part than do the repair, don't know what I was afraid of!

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Remove the glass cover to the halogen lamp fixture (counter clockwise turn, about a 1/4 turn). Recommend use of rubber coated gloves as the glass covers do not offer much by way of a good grip. Gently remove the halogen lamp (bulb) and insert new bulb into socket. Since the oven door is open, the lamp will light up indicating successful installation. Replace the glass cover (clockwise turn) until secure. Pitch the burnt out halogen lamp in the trash.

Removed two screws to access burner. Removed three power clips from burner, reattached the clips to new burner, removed brace clips and attach to new burner, close lid and reattach stove cover.