PGB975SEM4SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from Lebanon, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven wouldn't turn on
To get to the element I had to remove the lower cover from inside the oven.
After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.
Installation of the new one was simply the reverse.
Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.
The oven now works as it should.
After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.
Installation of the new one was simply the reverse.
Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.
The oven now works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Sheboygan, WI
- Parts Used:
- WB35X29668
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Oven door gasket was damaged and leaking
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from WESTFIELD, IN
- Parts Used:
- WB13T10065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Failed ignighter
Repair is easy. The keeper ring installation while holding the spring down was tricky. An extra set of hands is helpful in holding and replacing the keeper ring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIE from SYLMAR, CA
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Burner knob appears to be no longer available.
I have requested this part with the original p/n WB03K10303 and
p/n AP396896. Each times I received a different part than part I ordered. Has this parts been revised? The shaft of the knob is to to small
to to slide over burner controller stem.
p/n AP396896. Each times I received a different part than part I ordered. Has this parts been revised? The shaft of the knob is to to small
to to slide over burner controller stem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERNEST from MANCHESTER, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from PAINESVILLE, OH
- Parts Used:
- WB20K10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace temp sensor in gas range
Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from NAPLES, FL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom badly marred after 16 years.
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
Was this instruction helpful to you?
Thank you for voting!