P2S975CEM3CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- O.Robert from Montrose, PA
- Parts Used:
- WB13T10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The electrode had broke
I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CYPRESS, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very easy
there were no grate pads so it was easy to add them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chelagh from Fredericksburg, VA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
Nothing technical.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Homosassa, FL
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven will not heat
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tijeras, NM
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate foot bdroke off allowing grate to scratch cooktop
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Simi Valley, CA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Knoxville, TN
- Parts Used:
- WB13X46909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spark module would constantly spark
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R from Asheville, NC
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing meat thermistor
plug in thermistor when needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!