JGBP28CEM6WW General Electric Range - Instructions

just removed the old burner cap and put on the new one.

Secured the power, Opened the back of the range, and discovered a rodent chewed the wires in half so I striped the ends and wired them back together, the oven works great !!

Removed oven door, warming drawer, oven bottom, oven burner, disconnected wires to igniter. Also, instructions said to turn off gas supply at pressure regulator, {little red lever.} I also turned off main gas supply, and un-plugged power cord. Removing the igniter and replacing with new one was easy. Splicing wires and putting everything back together was also pretty easy. The only problem was when I tryed to open the gas to the pressure regulator, the little red lever popped off. Very cramped area to work in, could'nt get a tool to fit in there. So, I got some nylon string, made a loop, looped it on the notch on the pin, pulled it out and got the little red lever back onto the pin and then was able to open the valve. There is no gas going to the burner if that lever is not on holding the pin out, and you can't put that lever back on unless the pin is pulled out. If I ever do that job again I will not touch the red lever, I will just shut off the main gas supply. It would have been a pretty easy fix if that lever would not have popped off.

The part was very easy to switch out but it made no difference whatsoever so I returned it. The way it is designed is the problem. There is a pie slice shaped gap on the burner which causes a gap of no flame. Also a C shaped cut out around the igniter which causes another no flame gap.

remove screws, re-install screws

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

First replaced temperature sensor following YouTube instructions.

Then removed upper back panel to expose the control board. Removed the screws holding the control board, but DID NOT disconnect the wires. Moved the old control board up over the top of the range to let it rest on the stove top.

Fit the new overlay on the new control board. There are edges on the bottom and one side of the control board that makes aligning it easy.

Then ONE AT A TIME, starting with the largest connector on the end of the board, disconnected a lead and reconnected to the new board. NOTE: THE CONNECTORS ON THE NEW BOARD ARE IN DIFFERENT LOCATIONS THAN ON THE OLD! But if you look closely, they are all labeled. Simply find the same label on the new board and connect the lead from that connector on the old board. Making the right connections is NOT a problem. And there are connectors on the new board that are NOT USED! A note in the packaging warns of this.

Remounted the control board, replaced the back panel, and plugged the range back in. The new control board flashed all the LEDs and the clock started blinking. Set the clock. Turned the oven on and confirmed that it lit, cycled on and off during preheat, and beeped when it came out of preheat.

Since this was a new sensor and a new control board, I used my DMV and thermocouple to check the min/max temp during the heating cycle. Had to calibrate the temp down 5 degrees. Instructions for doing this are on the web and in the owners manual. It is easy.

Finally, did the GE Biscuit Test (Google it) and the biscuits were a bit under baked at the minimum time and a bit over baked at the maximum time. Perfect!

Everything fit, everything worked, took about 45 minutes start to finish. Wife is happy and I'm getting baked goodies again!

Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.

Since I'm not very mechanical I had my service manager from work come to my house and fiqure out the problem. By using an electrical meter he found that there was no continuity in the igniter. So being the mechanical guy I am I watched him take out 2 screws that secured the the piece of metal that covers the bottom part of the stove. He pulled that part out and from there it was 2 screws to release it from the back of the stove and 2 more to disconnect the igniter from the burner tube. We ordered the part and it arrived in 3 days. I opened the box and to my dismay it was broke. I called to tell them that it was broke and they ordered me a new one right then. I had that part the next day very grateful for that. I was able then to put it back together myself and it worked. Wife is extremely happy with me.

Remove the existing burner and install the replacement.

I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

Very was ti replace racks and knobs. Very fast mail service