JGBS23DEM6CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Myra from SCOTLAND, MD
- Parts Used:
- WB19K10044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my ignitor stopped working ,then the gas pressure regulator and safety valve needed replacing.
Super easy for me! My son-in-law is a contractor, I gave him the parts and let him do the work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from unadilla, NY
- Parts Used:
- WB28K10190
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Front orifice tube broke
The repair went easy the tube was a perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Dexter, GA
- Parts Used:
- WB27K10356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven stays in Preheat mode
first i changed out the temperature sensor that was bad did a ohms check on the old sensor an it showed OL on my meter, after installing new sensor then got a F4 code on display pad changed TO9 Control and that fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from SAHUARITA, AZ
- Parts Used:
- WB32K10036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven door gasket tore
Slid the oven door off of the hinges and laid it on a sheet on the kitchen island counter top. By simply looking at the spring clips on the new door gasket it was obvious how to use pliers to squeeze the clips on the broken gasket to easily remove it. I took the opportunity to clean the oven door before putting the new gasket on. Installing the new gasket was very easy, simply inserted the spring clips into the holes on the door and pushed until I heard the "click". Anyone can do this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Aldan, PA
- Parts Used:
- WB35K10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old bottom oven was really crusted and way too hard to clean.
Removed oven door.Opened slightly and lifted off.Removed two screws from rear of oven bottom.Lifted out bottom oven.Reversed for installing new bottom. Looks great.And the price was well worthit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Roseville, MI
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
open cook top / tubs pulled out front of stove
unplug power and turn off gas/// had to remove all star screws on top/remove ign wire from each burnner/now remove stove top/ adj wrench and remove nuts from the front nobs and relace with new front orifice tubes NOTE: Front orifice tube is the leftside. Front orifice HOLDER is the right side. put back top, open front to put hand in to make adjustments to ign wires close top and reinstall star screws and using finger to hold and make adjustments on top now turn power and gas on. I use soapwater to test for leaks/ leo gubin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Riverside, RI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hot Spot On Burner
Replaced old burner element with new, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Jessup, PA
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Bent/Broken Front Orifice Tubes
I removed the two nuts that secure the rear orifice tubes. This allowed me to lift the range top to access the broken tubes. Once lifted I removed the nuts that held the broken orifice tubes. I then connected the new orifice tubes. I removed the three(star)screws that fasten the orifice brackets under the range top. Doing this allowed me to connect the new tubes without having to maneuver them at all. I then lowered the top just enough to reattach the brackets. After securing the rear tubes I snapped the range top back into place. Just remember, if you use propane for cooking then you must remove the brass orifices from the old tubes and place them in the new ones. If you don't do this then your flame will not burn properly. Simply unscrew them from the old tubing and put them in the new tubing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!