JGBS80DEM2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marlo from CHANDLER, AZ
- Parts Used:
- WB48T10095, WB31K10217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old, scratched top griddle
Lift out old one and replace with new one. Also ordered an additional oven rack.
Their website is super easy to navigate and their availability of parts it's outstanding!!
Their website is super easy to navigate and their availability of parts it's outstanding!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from BRICK, NJ
- Parts Used:
- WB04K10021
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace Gasket to Oven
Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from DEARBORN, MI
- Parts Used:
- WB13X26360
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
One burner would not light from spark. All other burners lite with spark.
First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY
I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.
All burners have been working perfectly since the fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Apple Valley, MN
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bottom trim had rusted, so we needed new piece
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from REDDING, CT
- Parts Used:
- WB35X37973
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Hard to remove screws & no instructions that a heat shield had to be transferred from old to new
One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SAINT LOUIS, MI
- Parts Used:
- WB20K10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven not lighting
Secured the power, Opened the back of the range, and discovered a rodent chewed the wires in half so I striped the ends and wired them back together, the oven works great !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Sarasota, FL
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rusted trim strip
remove screws, re-install screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrico from DURHAM, NC
- Parts Used:
- WB20K10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
F 3 code came on my panel, the oven wasn’t getting to the right temperature
I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from West Melbourne, FL
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from WARROAD, MN
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from FAYETTEVILLE, NY
- Parts Used:
- WB07K10250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ESTELA E from HOUSTON, TX
- Parts Used:
- WB16T10046, WB29K10006, WB01K10008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No burner
I just put everything on it and lighted match and problem solved! Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karin from ARUNDEL, ME
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas burner wasn’t burning properly
I ordered the new burner head and replaced it and now it works perfectly.
Was this instruction helpful to you?
Thank you for voting!