JGBP25DEM8WW General Electric Range - Instructions

Replacing the igniter was easy to do, that only took 15 min. The time was needed to take apart the bottom of the oven so I could get to the nuts on the igniter, and the time to put it back together again. I'm very inexperienced at this sort of thing so since I could do it I'd encourage anyone to give it a go, and anyone that knows what they're doing will do it much faster.

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.

1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.

took off the door it should be very simple by opening the door just a little bit then pull up the door take out the shellves than take of the bottom of oven usualy there's 2 cap screws in back holding it down then take out the drawer from under the oven & unscrew the bracket that holds the flame pipe from underneath also unscrew the screw from inside the oven the holds the actual flame pipe in front next to the door then unscrew the old igniter from the pipe snip the old wire going out from the igniter & strip it a little & connect the new igniter put on the ceramic cover supplied together with the new igniter connect it back to flame pipe put everything back together you should be done. But make sure the wires are pushed down to underneath as much as you could also when you put back the gas pipe the wire should not be in the way underneath the oven

I'm still repairing. The igniter was replaced with new but it still doesn't glow. I'm waiting for a schematic that is being mailed to me from GE. In the meantime I have borrowed a test instrument to check that the system is hot when the BAKE button is pushed. The controls light up as expected but no glow. The BROIL igniter glows when activated, lighting the broiler. The new Ignite was packaged very well so it isn't suspect. I LEFT YOU FOR A FEW HOURS. I tested the electrical with a meter and got zero voltage. I removed the wire nuts and using two alligator clips I connected the meter to the bare wires coming from the oven wall. I then hit BAKE again and BINGO! Replaced the defective wire nut and now the igniter is happy as a clam. --- Thanks for your interest and for expediting the material.

Very very simple repair!!!!! Works great!!

Replace igniter in oven. It was a simple repair and only required that I unplugged the power cord from the unit, remove the base and 2 screws holding the igniter.

I only wish I would have taken the drawer out first to get at the wire connections. Instead I tried to get at them by trying to remove all the layers of sheet metal at the bottom of the oven - to no avail. Once I took the drawer out and saw the connections and bolts to remove that held the igniter/gas diffuser there was no problem. The new igniter does not come with the connectors on the ends so I simply cut off enough wire from the old one and used the wire nuts that came with to splice the wires. Simple reconnect and now we're "cookin' with gas" again.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

The repair went easy the tube was a perfect fit

I removed lower drawer, removed oven door,
took out rear screws to oven pan,removed screws that attatch ignighter to oven wall,disconnected wiring and removed old ignighter. reversed process to install new part. total repair time was about 20 minutes. Also take into consideration that i am a building contractor familiar to appliance repair etc.

I removed the igniter by first removing the oven racks then the oven pan and oven catch pans. I open the lower draw to the oven and removed the drawer. I reached back under the oven and clipped the wires that run to the igniter and striped a half inch of plastic to expose the wire. I removed the igniter from the burner and replaced with new igniter. I then fed the wires back through the hole the cut wires came out of and used the wire nuts supplied to connect. Replaced other parts in reverse order and tested. Works great.

First had to disconnect the old igniter by removing screw with a small wratchet wrench. Then pull out approximately 3" of wire from the old igniter, cut off old igniter, attache replacement igniter with supplied wire nuts, shove excess wire back into wiring compartment and then attach the new igniter.

I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.