JGBP28MEM2BS General Electric Range - Instructions

Took 5 minutes to repair easy peasy??

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

Start by shutting off the main gas supply to the range and unplugging the electric cord.
You will first need to take the plastic control knobs of from each individual burner (they should slide straight off).
Next, you will need to remove two phillips head screws on the front face of the panel. They are located on the right side of each rear valve burner stem that is sticking out through the panel.
Next, open the oven door, locate and remove the three screws on the bottom of the front face panel. The front panel should now come off exposing the top burner manifold and all of the valve burners.
The next step would be to take the burner grates and each round burner cover off (no tools required). This will expose the top of each individual burner. You will see screws that hold each individual burner down to the stove top. On my stove the heads were all rusted and I could not remove them. If you can remove all four of your burners and disconnect the wire on each ignitor and set the burners aside.
Next, go back to the front of the stove where you took off the panel and you will see two metal clips on each side of the stove top. Push each one of these in with a screwdriver and gently lift up on the stove top. It should hinge up towards the back of the stove and give you full access to the burner valve you need to change.
Next, use a box end wrench (I think it was 1/2") and remove the gas line attached to the burner valve. After the gas line is removed, take out the bolt and clamp that holds the burner valve to the manifold. The old valve should drop out.
Install the new valve making sure the rubber gasket is seated properly, reattach the clamp and bolt and reinstall the burner tube line.
Before you put the range all back together turn the gas back on at the appliance shutoff. Locate the gas orifice for that particular burner and hold your thumb or finger over the hole. Turn on the burner and leak test the burner tube connection and where the valve is clamped into the manifold.
Shut the burner back off if the leak test passes and reassemble the stove.
If your burners won't come out of the stove because the screw heads are rusted off (like mine was), you can carefully lift the lid a couple of inches to gain access to the valve. Make sure you don't bend or kink any of the burner tubes.

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

Most trouble I had was removing the screws that were located under the bracket. I had to slip the oven door off first to give me more room. Very hard to get to these screws because of where they were located under the bracket. I had to twist and turn the old igniter to get to it. When finally removed, I replaced the old igniter with the new one using my own screws. I twisted the wires together, and replaced the baffles, the oven floor, and then the door. The oven fired up wonderfully! Thank you for your prompt service for getting me the part quickly and correctly.

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.

Replaced the oven igniter

took off the door it should be very simple by opening the door just a little bit then pull up the door take out the shellves than take of the bottom of oven usualy there's 2 cap screws in back holding it down then take out the drawer from under the oven & unscrew the bracket that holds the flame pipe from underneath also unscrew the screw from inside the oven the holds the actual flame pipe in front next to the door then unscrew the old igniter from the pipe snip the old wire going out from the igniter & strip it a little & connect the new igniter put on the ceramic cover supplied together with the new igniter connect it back to flame pipe put everything back together you should be done. But make sure the wires are pushed down to underneath as much as you could also when you put back the gas pipe the wire should not be in the way underneath the oven

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.