JGB800SEP1SS General Electric Range - Instructions

replace igniter

I removed the oven door, the base panel of the oven and slid out the broiler tray. Next, I pulled the wires out of the access hole in the back of the oven, then diconnected the modular plug and removed the 2 screws fastening the ignitor. I tested the ignitor with my ohm meter and found out that it did not have the necessary zero ohms resistance. The meter indicated an open circuit, so I ordered the replacement part, which was delivered in less than 24 hours. Then I reassembled everything and tried the oven. Works like new again.

oven and stove top burners worked fine, but broiler would not light. diagnosed problem as bad igniter. ordered parts on line and received them next day with regular shipping!

removed oven door and bake racks. removed old igniter and snipped wires.

installed new igniter and used ceramic wire nuts to attach wire leads.

reinstalled door and racks.

works fine. who knew home repairs could be so easy and fun!

At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.

My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.

thank you

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.

I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

I went on line found your web sight selected the igniter kit required for my stove. Your web site made it easy to select the part I needed after reviewing the diagram. It was very easy to install just unplug the old unit and plug in the replacement. I would recommend this site to others.
I saved a few dollars; just think if a tech had to come out?

First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.

Replaced the igniter. Quite simple.

I got my part in a couple of days during christmas and still got at pretty quick it was 5 screws unpluged the old one pluged in the new one put screws back and we were ready to cook, did all from inside the oven did not even move the stove very simple!!

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!