JGBS04PPM4WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Indianola, WA
- Parts Used:
- WB16K10061
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven pilot light glowed but would not light.
Sadly, we had order the whole burner assembly , when it was just the thermocouple that was burn up. Pull oven away from wall, access burner assembly, take panel off behind control knobs (4 screws)to expose thermocouple. Install new copper line (thermocouple is attached) in same place where old line comes out. This was kind of tricky , you have to fish it through the insulation. One half goes down to oven burner and one goes to top of oven for stove top burner. Once in place, screw nut down on both ends to hold in place. Put it all back together. No need to replace burner unit if that was not the problem. Now you have a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Flemington, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
My old burners were beyond the point of coming clean and made my stove top look bad.
My husband and I simply took the burner units out of the packing, took the old ones off, put the new ones in. The new units needed to be leveled, but the leveling nuts included fit perfectly, and the entire repair took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from grand canyon, AZ
- Parts Used:
- WB16K10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
thermo coupler bad
took stove apart and removed part,installed new parts
oven worked great thanks for the correct parts, itseasy to order from you
oven worked great thanks for the correct parts, itseasy to order from you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Callie from Bay, AR
- Parts Used:
- WB28K10376, WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
two of the burners were not working at all, the other two were blackening pots and pans
I turned off the gas flow to the appliance, removed the old oriface spuds with the adjustable wrench, inserted the new oriface spuds and tightened them with the adjustable wrench. The double burner assembly just dropped on. They fit perfectly. I did not have to use the leveling nuts that were included with the burners. The old levelers were still in place and set perfectly for the new burners. Very easy repair, and the range works like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Yucca Valley, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pies Boiled Over And Baked On Oven Bottom
Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Houston, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven rack missing when I purchased the house
I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANNE from HICKSVILLE, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Burners were burning the pans and flames coming out at all different angles of the burner
The toughest part of the repair was the preparation to remove the old burners. As a result of the burning there was a carbon residue on the burners, on the gas outlet feed to the burners. This took some scrubbing and removing the carbon residue. Bits had burned onto the outlet and had to be scrapped off. Once all cleaned, replacing the burners was easy just had to place the balancing nuts in place and put on the burners. One problem arose the hood of the stove did not go back in place after replacing the burners so I then removed the balancing nuts put back on the burners stove top hood fit back in place and burners operated properly. This part of the repair took five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Clayton, MI
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gasket pulled from clips.
Removed old gasket and pried out clips with screwdriver. Installed new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Santa Clara, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners very old / needed to replace
Very easy! Open the top of the stove, remove the old double burner and place the new one! Anyone can do it! It's that easy... :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- noreen from flushing, NY
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mchael J. from Chesterfield, VA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from 29 Palms, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom tray would not clean up.Looked like finish was off it
removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ARDMORE, PA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward J. from CANASTOTA, NY
- Parts Used:
- WB16K10061
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
pilot wouldnt stay lit shut gas off for repair.
Dissassembled top of stove, removed porcelain top. unhooked pilot sensing line from oven thermostat. Removed bottom slide out drawer to gain access to pilot and burner assembly. Removed pilot thermocouple and burner assembly. Pulled down old pilot sensing line through insulation @ back of stove. Shoved new pilot sensing line up into insulation @ back of stove. Used long hook to pull line up through insulation. Installed new pilot thermocouple burner assy in bottom. Hooked up new sensing line to oven thermostat.Reassembled top components, lit pilots and tested operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from New Paltz, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burner not firing properly
ordered parts, 2 double burners, 3 days later they arrived.opened box.
lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID.
units purchased were exact replacements. supplied spacer nuts not needed.
easy fix looks new again, thanks.
lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID.
units purchased were exact replacements. supplied spacer nuts not needed.
easy fix looks new again, thanks.
Was this instruction helpful to you?
Thank you for voting!