JBP23DN1WW General Electric Range - Instructions

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

I removed the rear cover from the stove then removed the knob and two screws on the front panel that hold the control in place. I then took the wires off the old control one at a time and placed them on the new control. Then I placed the control in position and tightened the two screws on the front panel, replaced the knob and screwed the back panel in place.

called service co. and described problem while i was looking at parts diagram and he agreed with my feeling what part got fried. he told me the part would be 183.00 plus labor and drive time. when i told him i was looking at the part on line for 65 dollars he hung up on me. i recieved the part and was slightly dissapointed to know there was a sepperate adhesive overlay. i saw that it was a sepperate part but if i knew it was adhesive i would have spent the extra 20 dollars for a new one. but, to my surprise the old one peeled off easily and gently re-apllied it to the new conrol board alighning it well seemed to be the trickiest part of the job. took the five wires with connectors out of the old one and inserted them into the same place on the new one. removed the old one from the frame (4 pan phillp sheet metal screws) and then screwed the new wired control board in. plugged in the unit and pressed the bake button and then mixed the brownie batter. replaced the back panel cover. 65 dollars and 15 minutes.

thanks

bob

Very easy repair. The gasket ends are stuffed into slots right below the oven window and the gasket is held in with small wire clips that pop into holes in the door. Just pull the old gasket off, no tools. Install the gasket starting by stuffing one end into the slot mentioned above until the first clip lines up with the first small hole. Then insert each successive clip into the corresponding holes. Then use a slot screwdriver to stuff the other end of the gasket into the second slot. No sweat.

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.

first slide out range from wall and unplug it. then remove the rear panel, it is about 6 or 8 1/4" screws. remove the selector knob on the front of range and then remove the two philips head screws. this is how you remove the burner controller. hold the new controller next to the od one and one by one take the wires off the old one and put them on the new one. re-assemble and you are good to go.

I started by lifting the front of the stove and slipping a towel under it so it would slide easier and not scratch the floor. The next step was to unplug the stove, after that, I removed the shelves. The next step was to remove the cover plate on the b ack to expose the connection. I removed the old element by pulling the to slide-on connections and the two mounting screws. At this point I took the time to clean the oven since the element was not in the way. To install the new element I did the opposite of th removal process.

First, I made sure the power was turned off at the breaker box so I didn't electrocute myself. Then, I took out the 2 screws that hold the element in place, then pulled it out and unplugged the wires.
I plugged the wires onto the new element, and replaced the screws. My daughter could have done this....

The repair was simple. All wires were color coded and the new part had the same color codes marked. Simply unplugged the wires from the bad part and plugged them into the new part a reinstalled the part to the back panel of the range.

1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on

note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.

I used a screwdriver and pliers. A nut driver would have been helpful. Oven door is removeable for cleaning and maintenance, but it's heavy and awkward. It has to be laid face-side down to disassemble, so have a protected tabletop ready to avoid scratches. Side trim pieces have to come off to get access to bottom trim mounting screws.

Took old racks out, slid new ones in....exact match at a huge savings from what GE wanted per rack.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.

The known problem: a short occured between the surface element and the INF switch. After replacing the wire between the surface element and INF switch. The surface indicator light remained on - indicating a power surge/spike. Prior to removing the old INF switch I disconnected the wires from the old switch one at a time and plugged each into the new switch terminals. Then I removed the knob from the front of the control panel and the 2 screws holding the old INF switch in place. Removed the old switch and replaced it with the new switch. Reinstalling the 2 screws and the knob. Surface indicator light was no longer illuminated and surface element works fine.

Two screws on the inside to free element. 4 screws in the back to remove a plate. unhooked element connectors. Remove element from inside replace with new one. Too Easy.