All Installation Instructions for General Electric Range JB705TT1WW

Customer:: Don from Flagstaff, AZ
Parts Used:: WB35T10209
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Wrench set

dead mice in insulation, chewed wire on latch switch

replaced insulation

Was this instruction helpful to you?

Customer:: John from Woodbridge, VA
Parts Used:: WB25T10041
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Orange light "Hot Stovetop" lense broke off.

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

Was this instruction helpful to you?

Customer:: David from Lisle, IL
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

oven not warming, f2 indicating overheat

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Was this instruction helpful to you?

Customer:: Morris from Ardmore, TN
Parts Used:: WB24T10058
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Wrench (Adjustable)

Left front burner would only heat on high setting.

Identified part and part # using schematic found on GE website, contacted PartSelect and confirmed part number, ordered and paid for part. Two days later I recieved part. Unplugged stove, removed two screws on bottom side of front panel and two on top back of same panel, pulled panel forward, pulled the control knob off, removed two small screws that hold the control switch in place, situated new control switch next to bad switch and removed one wire at the time from the bad switch and connected to the same terminal on the new switch. Put everything back together and Bingo, works like a new one. Thanks PartSelect for the friendly, personal phone service, the fast shipment and competitive pricing on my part.

Was this instruction helpful to you?

Customer:: Ruth Ann from New Columbia, PA
Parts Used:: WB30T10133
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

The middle of the element quit working.

Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.

Was this instruction helpful to you?

Customer:: thomas j from canal winchester, OH
Parts Used:: WB07X42948
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Wrench (Adjustable)

Oven door trim rusted (bottom of door)

This repair is really easy unless the trim piece has rusted so badly that it's attached itself to the front door glass. It took a long time and some WD-40 to pry the trim off w/o breaking the glass. REPAIR: Remove the door and lay it on a flat surface. Unscrew the 3 bottom screws w/ small pliers, then unscrew the top two inside door screws w/ a small metric allen wrench. Remove the door trim to get to the last four side trim screws. Once the old trim is out just clean up any residue/rust remaining on the glass, install the new trim and reverse the steps to put the door back together. If the old trim comes off easily it should only take @ 20-30 minutes.

Was this instruction helpful to you?

Customer:: louis from pacific, MO
Parts Used:: WB56T10187
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench set

shattered front glass

Only had to take out 2 screws and 3 bolts, the new glass slid right in, there was alittle trouble lining up the bolt holes when puttung back together but that wasn't even realy that bad.

Was this instruction helpful to you?

Customer:: WILLIAM from Pinellas Park, FL
Parts Used:: WB56T10187
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

ge oven door glass replacement

the door glass was shipped super fast and was easy to replace. the only complaint i have is i wish they had some instructions with it i found some on utube. all you do is take the door off the hinges makes it alot easier to work on.

Was this instruction helpful to you?

Customer:: Gaetano A from Hamden, CT
Parts Used:: WB56T10187
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Oven Glass Door

Making repairs on glass is not always fun to do especially when you have make sure what the right torque is.. My decorative glass broke and I reached out to part select for a new one. They had exactly what I needed for the perfect price. Not too difficult to replace just do not over tighten, this might cause the glass to break again.

Was this instruction helpful to you?

Customer:: Edwin from HIGHLANDS RANCH, CO
Parts Used:: WB30T10133
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

one burner not working

Removed two screws to access burner. Removed three power clips from burner, reattached the clips to new burner, removed brace clips and attach to new burner, close lid and reattach stove cover.

Was this instruction helpful to you?

Customer:: Kenneth from Salem, OR
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Flashing F2 and erratic temperature readings.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Was this instruction helpful to you?

Customer:: jud from gatesville, TX
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

F2 error code

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Was this instruction helpful to you?

Customer:: Barbara from Jacksonville, FL
Parts Used:: WB56T10187
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

I broke the glass on the door & needed to replace it.

It was easy, it just fit in. I was afraid the part might not be right or that I would need extra parts but everything was great. Part arrived in 3 days. thanks

Was this instruction helpful to you?

Customer:: Lowell from Boulder, CO
Parts Used:: WB15T10176
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Socket set

broken handle on oven door

Used star screw driver to take door apart used socket set to unscrew handle screws. Installed new handle. Handle fit perfectly.

Was this instruction helpful to you?

Customer:: Gerald from Philadelphia, PA
Parts Used:: WB30T10129
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner not operational.

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Was this instruction helpful to you?

JB705TT1WW General Electric Range - Instructions